Its
cold start issues:---- Go
through the list of help links mentioned below:---- Click
the link :---- Cold start problem and vehicle shudder around 2500 to
3500 rpms ---------- http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html -------------- http://technoanswers.blogspot.in/2012/02/ford-explorer-40-will-not-idle-when.html -------- http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html ---------- http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-when-cold.html ----------- These
will help. Thanks.
http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html
Low idle when cold out side?
Ford explorer 4.0 will not idle when cold?
Automatic transmission shift lever hard to
move on cold mornings?
Car won't start when cold?
SOURCE: isuzu 2001 diesel engine won't start
cant start deisel 3.0 lilter sounds like there is no fuel getting to the engine
SOURCE: cold starting in the morning and when parked for a long time
try cleaning the start injector or replacing it this will fix your problem
SOURCE: how to find timing belts marks toyota rav4 2l
I have just replaced my water pump on my 1998 RAVE4, also, the timing belt and the other two belts. I had a tough time with the timing marks. The way you line these marks up is easy if you take the time, First, if you are changing the timing belt you pull the balancer and both top and bottom plastic covers,(do not try to pull top cover off before you take off balencer and the motor mount off or you will just break it.), Second after covers are removed you will have access to the timing belt, you can now remove it by loosening the tensioner bolt and pushing down on the tensioner wheel, the belt then can be taken off. Third take out number one sparkplug and replace the bottom cover by maybe two bolts so that you can see marks on cover, next replace the balancer and bolt. Turn the motor over by hand with the balancer so the small divit on the back of the balancer is on 0 or top dead center on the compression stroke, you can use a compression gauge for this or I just used a mirror and light to shine in the number one cylinder to see the piston. Next remove the balancer and cover and make sure to make a mark on crankshaft gear and housing. Next you will need mirror and flashlight, now turn camshaft gear clockwise to line the hole in the gear with the top timing mark. I recommend a small circle mirror for this. Now replace the belt. I turned the crank shaft gear one tooth counter clockwise off mark and the camshaft one tooth clock wise off mark so when the belt is on you can turn the camshaft gear counter clockwise to get tension on the belt and marks will line up. I would recommend changing water pump,tensioner wheel, and the idler wheel. After belt is on I would replace the bottom cover the balancer and the crankshaft sensor. Iwould then start it to make sure the water pump is not leaking and the motor is not pinging or you will have to tear it back apart again. Good luck and no I am not a certified mechanic just thought this would be helpful from my own experience.
SOURCE: (TOYOTA SURF 1990 TURBO DIESEL) No diesel coming out of fuel pump
my 3c diesel turbo engine start but for a few minute it kick off when i pump it continue running again
SOURCE: 2007 toyota rav4 cold start is slow
MAKE SURE YOU ARE USING THE CORRECT OIL WEIGHT. SOME WEIGHT CHANGES IN COLDER WEATHER IT WILL BE IN YOUR OWNERS MANUAL.2ND BATERYS TEND TO HAVE A 3 YEAR LIFE DO A LOAD TEST ON BATTERY AND I THINK YOU WILL FIND YOUR PROBLEM
Testimonial: "Timothy Reed Sorry I'm so late responding to your answer... Just learning a little on how to use this 'fixya' site... YOU WERE EXACTLY CORRECT !!! I would not have believed that it was the battery because it still did a good job of turning the engine. Had to replace the battery shortly thereafter... and that problem totally disappered and has never come back.. Thank you"
1,752 views
Usually answered in minutes!
×