Replace rear turn signal bulb on 2007 H3 - driver side

Replacing tail/brake/backup lights and turn signal bulbs (coupe)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. From inside the luggage

compartment remove the wing nut

of the rear light assembly cover.

3. Using a Phillips screw driver

remove the screw. The lamp is still

retained by a spring loaded clip.

Remove by gently pulling out the

light housing.

4. Turn the bulb socket counterclockwise as far as possible and pull it

out.

5. Pull the bulb straight out of the socket.

Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (sedan)

1. Make sure the headlamp control

is in the OFF position and then

open the trunk.

2. From inside the luggage

compartment remove the three wing

nuts of the light housing.

3. Gently pull the light housing to

the outside.

4. Turn the bulb socket

counterclockwise and pull it out.

5. Pull the bulb straight out of the socket.
Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (wagon)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. Using a screw driver remove the

fixings and trim from the body.

3. Remove the socket from the lamp

assembly

4. Pull the bulb straight out of the

socket.
Install in reverse order.


Hope this helps.

Zeppelinx12

Hello; To change bulbs remove the cover in the trunk (pull it away) Remove the nut's/wing nuts and the assembly will come out. If you ever have to change any of bulbs that are on the deck lid you will need to remove the covering on the inside of the deck lid, remove the assembly and change the bulb.

First,

1. Turn the engine off and open the hood. Pry up the two fasteners from the radiator air baffle with a flat head screwdriver. Move the baffle to the side to access the top of the headlight case.
   
2. Step 2 Pull up the two metal rods behind the headlight case. These secure the case to the car. You may need your pliers to pull them up.
   
3. Step 3 Gently pull the headlight case out to access its rear. On the rear, you will find several black dust covers. Twist off the dust cover closest to the fender (the outward dust cover) to access the turn signal bulb.
   
4. Step 4 Turn the bulb module counterclockwise to release it. Unplug the electrical connector from the bulb module. Connect the new bulb to the electrical connector (don't touch the glass with your hands; hold it by the plastic piece). Insert the bulb module in the turn signal housing, turn it clockwise and screw the dust cover back on.
   
5. Step 5 Insert the headlight case in the mount. Push the pins back down to secure it. Position the radiator baffle in its place and insert the fasteners.
   
Rear Turn Signal Bulbs
6. Step 1 Open the trunk. Remove the net from the side mounted wing nut (on the side with the faulty turn signal). Twist the wing nuts (there are two per side) counterclockwise to remove them.
   
7. Step 2 Peel the carpet layer back to access the rear signal lamp wing nuts. Twist these wing nuts (two per side) counterclockwise to remove them and release the rear signal.
   
8. Step 3 Carefully pull the rear signal assembly away from the Impala. The rear turn signal is the inner bulb (closest to the trunk). Press the tab on the bulb module and turn it counterclockwise to release it from the rear signal assembly.
   
9. Step 4 Pull the old bulb straight off the module (don't twist). Insert the new bulb in the module. Depress the tab on the connection and insert the module back in the assembly. Twist it clockwise.
   
10. Step 5 Insert the rear signal assembly. Re-attach the assembly's wing nuts and push the carpet layer back in place. Tighten the other two wing nuts to secure the carpet layer and reconnect the cargo net
    

PLEASE DON'T FORGET TO RATE!!!

Rear Turn Signal, Brake, & Marker Lights

1. Disconnect the negative battery cable.
   
2. Open the trunk.
   
3. Unfasten the nuts or other retainers from the rear trim.
   
4. Unfasten or release the housing cover retainers.
   
5. On some vehicles, you may have to remove the rear fascia/body panel and light assembly to get to the sockets.
   

On some vehicles, such as this 1986 Grand Am, you must remove the rear body panel with the lamp

Depending upon vehicle application, remove the lamp socket either by rotating it counterclockwise (approximately 1/4 turn) until the plastic tabs disengage, or by squeezing the metal tangs while pulling the socket from the light assembly


Remove the lamp socket assembly by turning it counterclockwise, then pulling it out

Generally, side marker lamps use small bulbs with flat, blade-type bases, and tail lights/turn signals use larger, round-based ("bayonet") bulbs.

1. Remove the bulb from the socket using the appropriate method. Bulbs with blade-type bases pull straight out, while those with round bases and protruding pins (bayonet-type bulbs) must be depressed, then rotated counterclockwise (approximately 1/8 turn) before pulling out.
   

Remove the side marker bulb from its socket by pulling straight out

To install:

1. Secure the bulb in the socket using the appropriate method. Bulbs with blade-type bases push straight in, while those with round bases and protruding pins (bayonet-type bulbs) must be inserted, then depressed and rotated clockwise (approximately 1/8 turn).
   
2. Install the lamp socket using the appropriate method. Depending on the type of socket, either engage the plastic tabs, and rotate the socket clockwise (approximately 1/4 turn), or push on the socket until the metal tangs engage.
   
3. Install the housing cover nuts.
   
4. If removed, install the rear fascia and light assembly.
   
5. Install the rear trim.
   
6. Connect the negative battery cable, then check the operation of the rear lights.
   

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Remove the 2 bolts as in the user manual. Slowly wiggle the tail light top then bottom as you pull straight back. Not slowly. There are 2 pin clips attaching it to the rear quarter panel.

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

look at the car manual under maintenance and then rear light bulb replacement. First take out the two hole covers using a flat head to loosen then wiggle and turn by hand to get out. Pull the light unit straight back, and unplug the electrical. Don't break anything.
Then use a star driver (check your misc socket set drivers for the right size). Unscrew the two star head screws and pull this bulb holder straight off the tail light (same direction as screws). Replace the bulb and put back together in reverse.

Tail light replacement is not as hard as it seems.
Tools needed:flat head screwdriver and a deep 5/32 socket(a pair of pliers will work).
Step 1: open trunk and pull back truck liner at tail light.There is a small button clip on liner.Use screwdriver to pop up the center of button clip,pull clip out of hole.
Step 2:You will see a black wire attached to the body of car with 2 white clips.Use screwdriver to pop clips off of studs.
Step 3:Remove the nuts from the studs and pull tail light assembly straight back away from car.The outer side of the light just snaps in and out of place.
Step 4:Turn light socket counter clockwise 1/3 turn and pull out.
Step 5:Pull bad bulb straight out and replace.Reverse steps to reassemble.

*The Turn signal on the Side of the car next to the headlight*
1. Open the retractable headlights.
2. Remove the plastic shroud around the headlight: two screws in front and one on each side.
3. Look to the outside of the headlight and you will see a single screw in a small plastic cover on the front inside edge of the signal light assembly. The headlight prevents you from getting at the screw straight-on. I broke it loose with an offset phillips screwdriver, and then backed it out with a regular phillips.
4. Remove the plastic cover, and you will see two screws. Remove them.
5. Now you can pull the turn signal assembly forward and out.
6. To remove the bulb holders from the assembly, twist counterclockwise and pull out.
7. Pull straight outward to remove the bulbs. To assemble, follow the steps in reverse. Note that there are two plastic rods on the back end of the turn signal assembly that you will insert into two holes in the channel of the fender

*The turn signal in the bumper*
1. You will need a phillips head And Flat head screw driver, right below the turn signal there is a panel that you can pop out, (or its allready gone, Looks like a Fog light can go in there.)
2. once u find that, (Pretty easy to find) Look directly up in there., there is styrofoam up there and u will also notice a little hole,
3. Stick the Phillips head screw driver in that hole and turn it counter clockwize, The screw will not fall out,
4.once it feels like the screw is loose put the flat head in between the turn signal lense and bumper, the side where you unscrewed it and SLOWLY pry it out,
4. once out, just twist the plug and replace light bulb
to replace just reverse instructions