NO POWER OR GROUND TO IGNITION COIL

Why ?? what a hack job ! can't fix it right take it to a qualified repair shop

Take it to the dealer or a ASE certified repair shop .

Description

*: ECM determines the start signal status by the signals of engine speed and battery voltage.
The ECM activates the fuel pump for several seconds after the ignition switch is turned ON to improve engine start ability. If the ECM receives a engine speed signal from the camshaft position sensor (PHASE), it knows that the engine is rotating, and causes the pump to operate. If the engine speed signal is not received when the ignition switch is ON, the engine stalls. The ECM stops pump operation and prevents battery discharging, thereby improving safety. The ECM does not directly drive the fuel pump. It controls the ON/OFF fuel pump relay, which in turn controls the fuel pump.

Component Function Check
1.CHECK FUEL PUMP FUNCTION
1. Turn ignition switch ON.
2. Pinch fuel feed hose (2) with two fingers.
1 : Air cleaner assembly


Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ON.
Is the inspection result normal? YES >> INSPECTION END
NO >> EC-466, "Diagnosis Procedure".
Diagnosis Procedure
1.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Turn ignition switch ON.
4. Check the voltage between ECM harness connector and ground.


Is the inspection result normal? YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-II
1. Turn ignition switch OFF.
2. Disconnect IDPDM E/R harness connector F10.
3. Check the continuity between IPDM E/R harness connector and ECM harness connector.

Is the inspection result normal? YES >> GO TO 3.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK CONDENSER-1 POWER SUPPLY CIRCUIT-I
1. Reconnect all harness connectors disconnected.
2. Disconnect condenser-1 harness connector.
3. Turn ignition switch ON.
4. Check the voltage between condenser-1 harness connector and ground.


Is the inspection result normal? YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK 15A FUSE
1. Turn ignition switch OFF.
2. Disconnect 15A fuse (No. 32) from IPDM E/R.
3. Check 15A fuse.
Is the inspection result normal? YES >> GO TO 6.
NO >> Replace fuse.
5.CHECK CONDENSER-1 POWER SUPPLY CIRCUIT-II
1. Disconnect IPDM E/R harness connector E18.
2. Check the continuity between IPDM E/R harness connector and condenser-1 harness connector.

3. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 13.
NO >> GO TO 7.
6.DETECT MALFUNCTIONING PART
Check the following.
??? Harness connectors E29, B10
??? IPDM E/R connector F10
??? Harness for open or short between IPDM E/R and condenser-I
>> Repair open circuit or short to power in harness or connectors.
7.CHECK CONDENSER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect dropping resistor harness connector.
3. Check the continuity between condenser-I harness connector and ground.

4. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 8.
NO >> Repair open circuit or short to power in harness or connectors.
8.CHECK CONDENSER-1
Refer to EC-469, "Component Inspection (Condenser-1)".
Is the inspection result normal? YES >> GO TO 9.
NO >> Replace condenser-1.
9.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-III
1. Disconnect ???fuel level sensor unit and fuel pump??? harness connector.
2. Check the continuity between IPDM E/R harness connector and ???fuel level sensor unit and fuel pump??? and ground.

Is the inspection result normal? YES >> GO TO 11.
NO >> GO TO 10.
10.DETECT MALFUNCTIONING PART
Check the following.
??? Harness connector E29, B10
??? Harness for open or short between ???fuel level sensor unit and fuel pump??? and IPDM E/R
??? Harness for open or short between ???fuel level sensor unit and fuel pump??? and ground
>> Repair open circuit or short to power in harness or connectors.
11.CHECK FUEL PUMP GROUND CIRCUIT
1. Check the continuity between ???fuel level sensor unit and fuel pump??? and ground.

2. Also heck harness for short to power.
Is the inspection result normal? YES >> GO TO 12.
NO >> Repair open circuit or short to power in harness or connectors.
12.CHECK FUEL PUMP
Refer to EC-469, "Component Inspection (Fuel Pump)".
Is the inspection result normal? YES >> GO TO 13.
NO >> Replace fuel pump.
13.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
Is the inspection result normal? YES >> Replace IPDM E/R.
NO >> Repair or replace harness or connectors.
Component Inspection (Fuel Pump)
1.CHECK FUEL PUMP
1. Turn ignition switch OFF.
2. Disconnect ???fuel level sensor unit and fuel pump??? harness connector.
3. Check resistance between ???fuel level sensor unit and fuel pump??? terminals as follows.


Is the inspection result normal? YES >> INSPECTION END
NO >> Replace ???fuel level sensor unit and fuel pump???.
Component Inspection (Condenser-1)
1.CHECK CONDENSER
1. Turn ignition switch OFF.
2. Disconnect condenser-1 harness connector.
3. Check resistance between condenser-1 terminals as follows.


Is the inspection result normal? YES >> INSPECTION END
NO >> Replace condenser-1.
Fuel injector Description The fuel injector is a small, precise solenoid valve. When the ECM supplies a ground to the fuel injector circuit, the coil in the fuel injector is energized. The energized coil pulls ...
Ignition signal Description The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induc ...
Other materials: Heater & cooling unit assembly
Removal and Installation COMPONENTS 1. Steering member 2. Heater and cooling unit 3. Blower unit REMOVAL 1. Discharge the refrigerant from the A/C system. Refer to HA-24, "HFC-134a (R-134a) Service Procedure". 2. Drain the engine coolant from the cooling system. Refer to CO-1 ...
On-vehicle repair
WHEEL HUB Removal and Installation 1. Knuckle 2. Baffle plate 3. Wheel hub assembly 4. Brake rotor 5. Wheel nut 6. Anchor block 7. ABS sensor 8. Parking brake cable A. Refer to PB-6, "PEDAL TYPE : Exploded View" (Pedal type), PB-7, "LEVER TYPE : Exploded View" (Leve ...
P0011, P0021 IVT control
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0011 or P0021 is displayed with DTC P0075 or P0081, first perform the trouble diagnosis for DTC P0075, P0081. Refer to EC-1191, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previousl ...

Pull off a spark plug wire and ground it over the engine. Crank the engine over and see if there is any spark from the wire. Sounds as if there is no spark to light the fuel you are putting in the carb. If no spark, possible ignition module/pick up coil inside the distributor/defective distributor cap/rotor/ignition coil/ wiring

Check to see if your timing belt is still in tact. If it is then you may need an new alternator.

Check the pcm ground pins to make sure they are grounded. 6, 28, 34, and 55.

Most cars are designed to only put power to the pump for a few seconds till the rpms reach a certain point so it doesn't keep pumping if engine stops. If you have power while cranking and you didn't have someone turn key on and watch test light right away you could have not noticed having power with key on and you probably have a bad pump. Also did you check to see if you had good ground in plug also? I would say if you have power and ground at plug pump is bad.

It has 2 feeds.If you run a ground to the ground side of the relay,engine turns over but doesn,t run ????? The PCM - engine computer isn't supplying the ground for some reason . Anti-theft system problem . Disables fuel an starting systems . Have you checked for codes ?DTC'S - diagnostic trouble codes .

#1 NEED TO VERIFY SPARK AT SPARK PLUGS # 2 CK FUEL PRESSURE AT SCHRADER VALVE ON FUEL RAIL ,,PRESSURE DEPENDS ON TYPE ENGINE ....IF NO SPARK AT SPARK PLUGS CHECK SPARK FROM COIL WIRE , IF NO SPARK AT COIL ,CHECK VOLTAGE TO IGNITION COIL SHOULD BE 12 VOLTS, IF NO VOLTAGE AT COIL ( KEY ON ) CHECK FUSES THEN IGHITION SWITCH. IF NO FUEL PRESSURE AND FUEL PUMP RUNS REPLACE PUMP .. CK VOLTAGE TO FUEL PUMP WHILE CRANKING . CK USING PUMP GROUND WIRE AT THE PUMP CONNECTOR THIS WILL PROVE GROUND ALSO. USE TEST LIGHT TO VERIFY

Sounds like an AUTOMATIC SHUTDOWN (ASD) RELAY problem. Fairly common on the Caravan.
Heres a brief overview of the ASD.
The Powertrain Control Module (PCM) operates the Auto Shutdown (ASD) relay by switching the ground path on and off.
The ASD relay supplies battery voltage to the fuel injectors, electronic ignition coil and the heating elements in the oxygen sensors.
The PCM controls the relay by switching the ground path for the solenoid side of the relay on and off. The PCM turns the ground path off when the ignition switch is in the Off position unless the 02 Heater Monitor test is being run. Refer to On-Board Diagnostics. When the ignition switch is in the On or Crank position, the PCM monitors the crankshaft position sensor and camshaft position sensor signals to determine engine speed and ignition timing (coil dwell). If the PCM does not receive the crankshaft position sensor and camshaft position sensor signals when the ignition switch is in the Run position, it will de-energize the ASD relay.
The ASD relay is located in the Power Distribution Center (PDC). The PDC is located on the driver's side inner fender well Power Distribution Center . A label on the underside of the PDC cover identifies the relays and fuses in the PDC
Check for good ground.
Good luck...i hope this helps, please rate me a fixya.