I want to change the fuel filter of My mazda premacy 02 but i don't know its location in the engine compartment
SOURCE: changing fuel filter on 2002 Mazda pickup
Clean all dirt and/or grease from the
fuel filter fittings. "Quick Connect" fittings are used on models
equipped with a pressurized fuel system. These fittings must be
disconnected using the proper procedure or the fittings may be damaged.
The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin
clip legs about 1/8 in. (3mm) each to disengage
it from the fitting, then pull the clip outward. Use finger pressure
only; do not use any tools. Push the quick connect fittings onto the
filter ends. Mazda recommends that the retaining clips be replaced
whenever removed. The fuel tubes used on these fuel systems are
manufactured in 5/16 in. and 3/8
in. diameters. Each fuel tube takes a different size hairpin clip, so
keep this in mind when purchasing new clips. A click will be heard when
the hairpin clip snaps into its proper position. Pull on the lines with
moderate pressure to ensure proper connection. Start the engine and
check for fuel leaks. If the inertia switch (reset switch) was
disconnected to relieve the fuel system pressure, cycle the ignition
switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
Remove the "hairpin" clip retainers to access the fuel line fittingsThe
inline reservoir type fuel filter should last the life of the vehicle
under normal driving conditions. If the filter does need to be
replaced, proceed as follows:
CAUTIONIf
the fuel filter is being serviced with the rear of the vehicle higher
than the front, or if the tank is pressurized, fuel leakage or
siphoning from the tank fuel lines could occur. to prevent this
condition, maintain the vehicle front end at or above the level of the
rear of vehicle. also, relieve tank pressure by loosening the fuel fill
cap. cap should be tightened after pressure is relieved.
The
flow direction arrow should be positioned as installed in the bracket
to ensure proper flow of fuel through the replacement filter.
To install:
SOURCE: Fuel Filter location on a Petrol 2004 Kia Carnival
The fuel filter is located in the fuel tank, pump removal is required to replace. There is an inspection cover behind the front seats on the floor to gain access to the pump. stupid idea. but whats not stupid about kia.
SOURCE: how do i replace the fuel pump in my 1993 mazda 626 2.5
1. Relieve the fuel pressure and disconnect the negative battery cable.
2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.
3. If not already done, detach the electrical connector from the fuel pump/sending unit.
4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.
5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.
6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.
7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.
To install:
1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.
2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.
3. Connect the fuel supply and return lines.
4. Install the access cover and the mounting screws.
5. Attach the sending unit electrical connector.
6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.
7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.
SOURCE: 2000 mazda 626 fuel filter location.engine
it should be on the driver side. very hard to get to. look under the air box were the air filter goes.
j.aguilar
1,893 views
Usually answered in minutes!
×