Tryin to replace cam position sensor on 98 chevy lumina . i have all the bolts out of the powewr steering pump and drive belt off but power steering pump won't clear to actually come out looks lik

• SERVICE AND REPAIR

Camshaft Sensor Follow this URL for picture:_
http://alldatapro.com/alldata/PRO~V416324719~C30660~R0~OB0~P3R0H~N/0/41746052/42417623/42417638/42422763/34853741/34857029/34857030/101366976/14461280/42437587/41882479

REMOVE OR DISCONNECT

• Negative battery.
• Serpentine drive belt and secondary air injection drive belt.
• Power steering pump.
• Electrical connector.
• Bolt (1). Refer to Figure.
• Camshaft sensor.

INSTALL OR CONNECT

• Camshaft sensor.
• Bolt (1) torque to 10 Nm (8 ft lb).
• Electrical connector.
• Power steering pump.
• Serpentine drive belt and secondary air injection drive be!t.
• Negative battery cable.

• SERVICE AND REPAIR

Camshaft Sensor Follow this URL for picture:_
http://alldatapro.com/alldata/PRO~V416324719~C30660~R0~OB0~P3R0H~N/0/41746052/42417623/42417638/42422763/34853741/34857029/34857030/101366976/14461280/42437587/41882479

REMOVE OR DISCONNECT

• Negative battery.
• Serpentine drive belt and secondary air injection drive belt.
• Power steering pump.
• Electrical connector.
• Bolt (1). Refer to Figure.
• Camshaft sensor.

INSTALL OR CONNECT

• Camshaft sensor.
• Bolt (1) torque to 10 Nm (8 ft lb).
• Electrical connector.
• Power steering pump.
• Serpentine drive belt and secondary air injection drive be!t.
• Negative battery cable.

YOU MUST REMOVE POWER STEERING PUMP, AND BELT THE SENSOR IS UNDER THE PUMP IN THE BLOCK.

Power Steering Pump Removal & Installation 2.2L Engine To Remove:

1. Remove the upper cooling fan shroud.
2. Position a fluid catch pan under the power steering pump.
3. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan. NOTE: On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
   
4. Remove the drive belt from the pulley.
5. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump. NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
   Installing the pilot bolt
   
   Removing the power steering pump pulley
   
   Installing the power steering pump pulley
   
   
6. Unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
7. Remove the front mounting bolts and the rear bracket nuts from the studs on the engine.
8. Remove the rear brace mounting bolt.
9. Remove the power steering pump from the vehicle.

To Install:

1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm).
2. Install the rear bracket bolt and nuts. Tighten the retainers to 22 ft. lbs. (30 Nm) on 1994 - 97 models and 37 ft. lbs. (50 Nm) on 1998 and later models.
3. Install the A/C compressor.
4. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
   
5. Properly install the drive belt.
6. Remove the caps, then connect the feed and return hoses to the pump.
7. Properly refill and bleed the power steering system.
8. Test drive the vehicle.

4.3L Engine To Remove:

1. Remove the upper cooling fan shroud.
2. Remove the drive belt.
3. Remove the fan and clutch from the water pump.
4. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
5. Safely raise and support the vehicle.
6. Remove the shield from the steering linkage.
7. Position a fluid catch pan under the power steering pump.
8. Disconnect the return hose from the power steering pump, then drain the excess fluid into the catch pan.
9. Safely lower the vehicle.
10. Disconnect the pressure hose from the pump and cap the open line.
11. Remove the filler neck tube.
12. Remove the power steering pump mounting nuts and bolts.
13. Remove the power steering pump from the vehicle.

NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
Installing the pilot bolt

Removing the power steering pump pulley

Installing the power steering pump pulley

To Install:

1. Position the pump to the vehicle.
   • Tighten the front retaining bolts to 37 ft. lbs. (50 Nm) and the nuts to 31 ft. lbs. (41 Nm).
2. Install the filler neck tube.
   • Tighten the bolt to 15 ft. lbs. (20 Nm).
3. Connect the pressure hose to the pump.
4. Safely raise and support the vehicle.
5. Connect the return hose to the vehicle.
6. Install the shield on the steering linkage and lower the vehicle.
7. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
   
8. Install the fan and clutch on the water pump.
9. Properly install the drive belt. NOTE: Be sure to secure any hoses which may get in the way or rub other components.
   
10. Install the upper fan shroud.
11. Properly refill and bleed the power steering system.
12. Test drive the vehicle.

Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal

1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
   

1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
   

1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.
   
   
   
   
   
   Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).
   
   
   
   
   
   Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner

1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .
   
   Remove the drive belt from the power steering pump pulley.
   

1. Remove the oil dipstick tube.
   

1. Remove the power steering pump support (3C511).
   

1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
   

1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).
   
   While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
   

1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
   

Installation

1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
   

1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
   

1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).
   
   Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
   

1. Install the drive belt on the power steering pump pulley.
   

1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
   On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
   

1. Install the power steering pump support, if removed.
   

1. Install the oil dipstick tube.
   

1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
   

1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
   

1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
   

1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .
   
   
   Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only
   
   
   
   
   
   Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
   (32-38 Lb-Ft)
   
   Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar
   
   
   
   
   
   Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

It could be various things.
Low steering fluid
Dirty steering fluid
Bad steering pump
Loose or missing belt
Bad steering box
Air in the steering system

I would check what you know how to check. If they're okay, have a mechanic check the rest.

1. Disconnect battery ground cable, then remove exhaust manifold heat shield.
2. Disengage power steering pump reservoir hose from pump bracket and engine lifting bracket, then disconnect return hose and reservoir pump hose from pump.
3. Allow fluid to drain into a suitable container, then raise and support vehicle.
   1. Remove lower belt guard, then rotate drive belt tensioner clockwise as viewed from direction shown, and remove accessory drive belt.
   2. Lower vehicle, then remove traction assist module bolts and position module aside.
   3. Rotate power steering pump pulley to gain access to each pump front mounting bolt, then remove three front bolts and one rear bolt and lift pump from vehicle.
   4. If it is necessary to separate pulley from power steering pump, proceed as follows:
   1. install power steering pump pulley remover T69L-10300-B, or equivalent, on pulley hub.
   2. Clamp hex head of tool in a suitable vise, then hold power steering pump in place while turning tool nut counterclockwise. Do not apply inward or outward force on power steering pump shaft, internal pump damage may result.
   3. Slide pulley from power steering pump shaft.
   1. Reverse procedure to install, noting following:
   1. If pulley and power steering pump were separated, install pulley on pump shaft using power steering pump pulley replacer T91P-3A733-A, or equivalent. Ensure threads on end of tool are fully engaged in power steering pump shaft; after pulley installation, ensure end of shaft is within 0.010 inch of being flush with pulley surface.
   2. When placing pump in vehicle, install rear mounting bolt first, but do not tighten until three front bolts are in position.
      1. Rotate drive belt tensioner clockwise as viewed from direction shown to install accessory drive belt.
      2. Refill power steering fluid reservoir and bleed system.

No i will post the procedure below.


3.4L REMOVAL OF CAM SENSOR

1. Turn OFF the ignition.

2. Remove the serpentine drive belt.

3. Disconnect the sensor electrical connector.

4. Remove the power steering pump, if required.

5. Remove the attaching bolt.

6. Remove the sensor.

7. Inspect the sensor for wear, cracks or leakage if the sensor is not being replaced.



To install:

1. Lubricate the O-ring with clean engine oil and replace if damaged.

2. Install the camshaft Position Sensor.

3. Tighten the retaining bolt to 8 ft. lbs. (10 Nm).

4. Connect the sensor electrical connector.

5. Install the power steering pump, if removed.

6. Reinstall the serpentine drive belt.

I don't have chrysler producs. I'll post 3.8L V6 Ford Windstar for reference. You'll get some idea.



Removal
WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.

1. Using a 15mm socket or wrench on bolt attaching drive belt tensioner pulley. Rotate drive belt tensioner (6B209) clockwise to remove drive belt from pulleys.
   
   3.8L Engine
   
   

Item Part Number Description 1 10300 Generator 2 3A674 Power Steering Pump 3 19703 A/C Compressor 4 6B217 Drive Belt Tensioner Pulley 5 6312 Crankshaft Pulley 6 8501 Water Pump 7 6B209 Drive Belt Tensioner 8 8620 Drive Belt
Installation

1. Install drive belt over all pulleys (except drive belt tensioner ).

1. Rotate drive belt tensioner as described under Removal and install drive belt over drive belt tensioner pulley. Ensure that all V-grooves make proper contact with pulleys

---------------------------------------------------------------
Another example
Pulley, Power Steering Pump CII
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal

1. Drain as much fluid as possible from the power steering pump (3A674) through the power steering oil reservoir (3A697) neck.

1. Install Steering Pump Pulley Remover T69L-10300-B on the power steering pump pulley (3A733) , and place the tool and power steering pump in a vise by gripping the small hex-head of the tool.

1. Hold the power steering pump , and rotate the tool nut counterclockwise to remove the power steering pump pulley . Do not apply in and out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
   
   

Installation
CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal thrust areas.

1. Place the power steering pump pulley on the power steering pump shaft, and install Steering Pump Pulley Replacer T65P-3A733-C. The small diameter threads on the tool should be fully engaged in the power steering pump shaft.

1. Hold the power steering pump , and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. The power steering pump pulley face must be flush within 0.25mm (0.010 inch) of the end of the power steering pump shaft.

1. Remove the tool.

1. Fill the power steering oil reservoir to the COLD FILL line.

------------------------------------------------------------------------------------------
Steering Pump, Power Removal

1. Disconnect battery ground cable (14301) .

1. Remove accessory drive belt (8620) .

1. Raise vehicle on hoist. Refer to Section 00-02 .

1. Remove right front wheel (1007) and tire assembly.

1. Remove power steering pump pulley (3A733) .

1. Position drain pan. Remove power steering pressure hose (3A719) and power steering return hose (3A713) from power steering pump (3A674) .

1. Remove four power steering pump retaining bolts (three in front, one in rear) and remove power steering pump .

Installation

1. Position power steering pump and install retaining bolts. Tighten retaining bolts to 41-54 Nm (30-40 lb-ft).

1. Install power steering pressure hose and power steering return hose to power steering pump . Remove drain pan.

1. Press on power steering pump pulley as outlined in this section.

1. Install right front wheel and tire assembly. Tighten lug nuts (1012) to 115-142 Nm (85-105 lb-ft).

1. Lower vehicle.

1. Install drive belt to power steering pump pulley .

1. Connect battery ground cable .

1. Fill power steering oil reservoir (3A697) to proper level. Refer to Section 11-00 .
   
   Power Steering Pump and Bracket, 3.8L
   
   

Item Part Number Description 1 N607528-S2 Screw, M6-1 x 16 2 8509 Water Pump Pulley 3 W804804-S2 Screw, M8-1.25 x 35 4 N806214-S2 Bolt, M12 5 W606691-S36B Screw, M8-1.25 x 35 6 10B315 Generator Brace 7 N621939-S36B Nut, M8-1.0 8 10300 Generator 9 6B212 Accessory Drive Belt Tensioner Bracket 10 6049 Cylinder Head 11 19D624 Air Conditioning Compressor Bracket 12 W606563-S2 Bolt, M10-1.5 x 55 13 19703 A/C Compressor 14 N807273-S100 Bolt, M8-1.25 x 121.5 15 3C510 Power Steering Hose Bracket 16 3A674 Power Steering Pump 17 3C511 Power Steering Pump Support 18 W807239-S8 Bolt, M10-1.5 x 36.5 19 2888 A/C Compressor Brace 20 W806342-S2 Bolt, M8-1.25 x 23 21 W606571-S411 Bolt, M10-1.5 x 113.5 22 6C348 Idler Assembly 23 3A733 Power Steering Pump Pulley 24 N805137-S56 Bolt, M10-1.5 x 157 25 N621939-S2 Nut, M8-10 26 N807241-S36B Bolt, M10-1.5 x 132 27 6B209 Drive Belt Tensioner A — Tighten to 8-11 Nm (71-101 Lb-In) B — Tighten to 20-25 Nm (15-18 Lb-Ft) C — Tighten to 70-95 Nm (52-70 Lb-Ft) D — Tighten to 40-55 Nm (30-40 Lb-Ft) E — Press Flush with End of Power Steering Pump Shaft

Park vehicle on level ground.
2. Remove battery from vehicle.
3. Remove air cleaner outlet hose, engine under cover ( right side ) and exhaust pipe # 2 .
4. Disconnect " B " terminal wire and coupler from the Alternator ( Generator ) .
5. Remove Alternator ( Generator ) belt.

6. Remove power steering pump. Do not disconnect hoses.
6. Remove Alternator ( Generator ) cover.
7. Remove Alternator ( Generator ) bracket mounting bolts.
8. Remove Alternator ( Generator ).

Power Steering pump has three bolts- 2 behind the pulley at 12 and 6 o'clock and one bolt on the back.

Once you get the power steering pump out of the way you can remove the last bolt on the alternator

Ok...I did not remove axle or disconnect hoses on power steering...I did unbolt power steering pump and moved off to side.

after that I disconnected sensor on throttle body and very carefully lifted alternator through the top where your air intake assembly would have been at, right next to A.C. refrigerant lines.It takes a minute , you HAVE TO BE CAREFUL NOT TO DAMAGE SENSOR!!

However it is a lot faster that taking off drive shaft and exhaust pipe!

If you go to AutoZone .com they have exploded diagrams of the parts you have to take off and they will show you bolt locations, the power steering pump bolt at 6 o'clock drove me crazy.

P.S. Get a ratcheting 12 mil wrench, it's a life and knuckle saver!!