How do I remove the rear bench seat on a Galant 2010 to install seat covers? Thanks

Question edited for clarity.
Question moved to model category.

How do I remove the back seat from a 2007 Chev Aveo ...

JustAnswer https://www.justanswer.com > Chevrolet Repair
Jul 18, 2010 - Lift and remove the rear seat cushion. ... Insert the wire loops along the front edge of the rear seat cushion into the recesses in the floor pan.
1 answer · Top answer: Hello, the seat is held in place via u shaped clips. there is one on each sie under ...

Backseat and Bench Removal?

Aveo forum https://www.aveoforum.com > forum > backseat-benc...
Dec 18, 2006 - Anyone have pics/instructions on how I can remove them? I want to remove for track reasons. 2006 Chevy Aveo LS Hatchback - getting sold soon
10 posts · should be straight forward... undo a couple of bolts, remove.
Reql seat removal, 2011 Aveo sedan
3 posts
Jul 25, 2018
How the heck do I fold down the rear seat in my Aveo5??
10 posts
Jun 1, 2010
Headrest removal? -- Chevrolet Aveo forum and ...
5 posts
Apr 29, 2010
2004 Aveo hach rear seats stuck down
2 posts
Feb 23, 2020
More results from www.aveoforum.com

How to remove back seat Chevrolet Aveo ? - victoriamgclub

victoriamgclub.com https://victoriamgclub.com > how-to-remove-back-sea...
Feb 21, 2020 - You will simply need to tilt the seat to the front and you will have access to the Torx nuts that hold it to the vehicle's chassis. Once these ...

If you have the long bench I don't think you can fold the rear seat down. It will only fold down if you have the split rear bench.

You should notice a looped strap of cloth next to the head rest at the top of the seat. That is the release for the seatback lock. Simultaneously pull up on the strap and pull the head rest forward to fold the seat forward. The seats are split 60/40, so each seat has its own release looped strap.

If I am not mistaken, you have to remove the head rests, remove the bottom bench, fold down the armrest and remove the bolts behind it (Note: At the bottom, the bolts for the seat are held in by a clip... You just take a flathead screwdriver and pry it forward and it will then release. Make sure you dont let the seat-belts retract; it be difficult to get it back.) Typically, it takes about 2 hours to remove the seats. You will also need a metric set of Allen and Socket Wrenches to remove the bolts.

I am going to assume you mean the normal rear seats, not rear facing seats in the very back.
The rear seat folds down. The benches fold up from the back. When they are up you can see how to easily remove them if you want.
When the benches are up the backs fold down. There are levers on the top the slide forward to release them so they can be folded down. Tip the outboard head restraints forward by pulling their straps. The center head restraint has a button behind its right-hand support that you push to allow it to be lowered.

I think you have to remove headrst bfore folding seat back down. You may have to unbolt seat from floor. 4 bolts.
Rear Seat Backrest —Split Bench Removal
NOTE: The 40% rear seat backrest must be removed before the 60% rear seat backrest.
40% rear seat backrest

1. Remove the 40% rear seat backrest.
   1. Remove the nuts and bolts.
   1. Remove the backrest.

60% rear seat backrest

1. Remove the 60% rear seat backrest.
   1. Remove the nut and bolt.
   1. Remove the backrest.

Installation
NOTE: The 60% rear seat backrest must be installed before the 40% rear seat backrest.
60% rear seat backrest

1. NOTE: Do not tighten the nut and bolt at this time.
   Install the 60% rear seat backrest.
   1. Install the rear seat backrest.
   1. Install the nut and bolt.

40% rear seat backrest

1. NOTE: Do not tighten the nuts and bolts at this time.
   Install the 40% rear seat backrest.
   1. Install the rear seat backrest.
   1. Install the nuts and bolts.

60/40% rear seat backrest

1. Tighten the 60/40% rear seat backrest nuts and bolts in the sequence shown.

40% Rear Seat Backrest

1. Tighten the 40% rear seat backrest nuts and bolts in the sequence shown.

There is a latch located behind the head rest on the rear deck area of the car. Good Luck

it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal

1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
   

1. Slide the bench seat forward to the center row seating position.
   

1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
   
   
   
   
   

1. Remove the bench seat from the vehicle through the body side door opening.
   

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

i dont think they were meant to fold down but you should be able to take them out to haul bigger items. some of the vans they make are made that way so that you have to remove the seats rather than fold them down