Bank 1 cam sensor
Camshaft Position Sensor
Camshaft Position Sensor Operation:
A magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.
SOURCE: where is bank 1 sensor 2 located on a 2005 honda
4 or 6 cylinder engine.
It's the rear O2 sensor,the one behind the catalytic converter.
======
Clear the code with OBDII scanner or remove negative cable for 2 minutes.
Wait until the exhaust cool for 1 hours
Disconnect the connector and clean the contacts with CRC electrical contact cleaner the contacts.
reconnect negative battery cable
Start the car and let the motor warm up.
====
If the code keeps coming back then you will need to purchase a O2 sensor socket + O2 to change it out.
Please rate my answer if it's helpful to you.
Cheers,
Mustgo.
I
SOURCE: where are bank 1 sensor 1, bank 2 sensor 1, bank 1
bank one sensor 1 is the bank of cylinders that number 1 spark plug is located in, bank 2 the other side, this assumes u have a V8, the sensor one location is the sensors that are BEFORE THE CATALYTIC CONVERTER, the sensors referred to as sensor 2 are after the ones AFTER THE CATALYTIC CONVERTER IN THE EXHAUST SYSTEM.
SOURCE: Where Are The sensor Banks On The 2004 GC
Grand Cherokee oxygen sensor locations for 4.0
and 4.7 engines
Four wires (circuits) are used on each O2 sensor:
O2S Sensor removal
Never apply any type of grease to the oxygen
sensor electrical connector, or attempt any soldering of the sensor
wiring harness.
WARNING: THE EXHAUST MANIFOLD, EXHAUST PIPES AND
CATALYTIC CONVERTER(S) BECOME VERY HOT DURING ENGINE OPERATION. ALLOW
ENGINE TO COOL BEFORE REMOVING OXYGEN SENSOR.
1. Raise and support vehicle.
2. Disconnect O2S pigtail harness from main
wiring harness.
3. If equipped, disconnect sensor wire harness
mounting clips from engine or body.
CAUTION: When disconnecting sensor electrical
connector, do not pull directly on wire going into sensor.
4. Remove O2S sensor with an oxygen sensor
removal and installation tool.
02S Sensor installation
Threads of new oxygen sensors are factory coated
with anti-seize compound to aid in removal. DO NOT add any additional
anti-seize compound to threads of a new oxygen sensor.
1. Install O2S sensor. Tighten to 22 ft. lbs. (30
N·m) torque.
2. Connect O2S sensor wire connector to main
wiring harness.
3. If equipped, connect sensor wire harness
mounting clips to engine or body. When Equipped: The O2S pigtail harness
must be clipped and/or bolted back to their original positions on
engine or body to prevent mechanical damage to wiring.
Hope thats help (remember comment and rated this).
Generic OBD II Diagnostic Trouble Codes
DTC CODES P0300 to P0399
P0300....Random/Multiple Cylinder Misfire Detected
P0301....Cylinder 1 Misfire Detected
P0302....Cylinder 2 Misfire Detected
P0303....Cylinder 3 Misfire Detected
P0304....Cylinder 4 Misfire Detected
P0305....Cylinder 5 Misfire Detected
P0306....Cylinder 6 Misfire Detected
P0307....Cylinder 7 Misfire Detected
P0308....Cylinder 8 Misfire Detected
P0309....Cylinder 9 Misfire Detected
P0310....Cylinder 10....Misfire Detected
P0311....Cylinder 11 Misfire Detected
P0312....Cylinder 12 Misfire Detected
P0313....Misfire Detected with Low Fuel
P0314....Single Cylinder Misfire (Cylinder not Specified)
P0320....Ignition/Distributor Engine Speed Input Circuit
P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance
P0322....Ignition/Distributor Engine Speed Input Circuit No Signal
P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent
P0324....Knock Control System Error
P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)
P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330....Knock Sensor 2 Circuit (Bank 2)
P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332....Knock Sensor 2 Circuit Low Input (Bank 2)
P0333....Knock Sensor 2 Circuit High Input (Bank 2)
P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335....Crankshaft Position Sensor A Circuit
P0336....Crankshaft Position Sensor A Circuit Range/Performance
P0337....Crankshaft Position Sensor A Circuit Low Input
P0338....Crankshaft Position Sensor A Circuit High Input
P0339....Crankshaft Position Sensor A Circuit Intermittent
P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)
P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)
P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)
P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)
P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)
P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)
P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)
P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)
P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)
P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)
P0350....Ignition Coil Primary/Secondary Circuit
210 views
Usually answered in minutes!
×