Turn Signal Switch where is it located

You replaced factory bulbs with led bulbs ? There is no relay BCM - body control module does it
Turn Signal Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.

Put the stock lamps back . LED's won't work .

The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side:
• The Rear Turn Lamp
• The Turn Signal Indicator
• The Sidemarker Lamp
• The Sideview Mirror (Pontiac Thunder only)
The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp.
The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass.
The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200.
When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off.

Did you change any wiring , tap into any wiring ? There is no flasher relay on your vehicle . It controlled by the BCM !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
Your best bet , take it to a qualified repair ! We on here have no clue what you did . On this newer vehicles ,if you know nothing about automotive electronics you really should take to a professional

check the fuses and both flasher cans,if not working then,u need to check the blinker switch

ON THIS YEAR 2 THINGS ARE USUALLY THE PROBLEM. THE TURN SIGNAL SWITCH OR THE HAZARD SWITCH. IT DOESNT HAVE A FLASHER. THE FLASHER IS INTEGRATED IN THE HAZARD SWITCH. ITS ABOUT 20 BUCKS FROM THE DEALER. THE TURN SIGNAL SWITCH HAS TO BE REPLACED AS AN ASSEMBLY. THE COLUMN COVERS HAVE TO COME OFF AND THE WHOLE ASSEMBLY NEEDS TO BE REPLACED

I Think your turn signal switch is most probably faulty. So that, you will need to replace it. Please, check the video below. It shows the operations to replace the turn signal switch. I think that the operations are quite similar in most modern cars. Good luck!

How to Easily Replace a Turn Signal Switch - Clio 2 and other Renault/Dacia

http://www.youtube.com/watch?v=JKiy-F8pd6o
How to Easily Replace Turn Signal Switch Clio 2 and other Renault Dacia

This is a common GM specific problem. Your turn signal switch contains an elaborate networking device that has to cancel brakelights while running a turn light. Often times the ground within the turn signal switch is lost causing your situation. After investigating such other possibilities as fuses and loose grounds it may become necessary to replace the turn signal switch. Thank you, Dana

replace the turn signal switch it self, mine did the same thing with the left turn signal, put in fuse and it will continue to flash... went to junk yard pulled one out of a 97 avenger just like mine, swapped them out and now it works fine. looked to be like some corrosion... to repace: 3 screws under columb, 2 screws on side of signal switch (black plastic side). unplug and replace

hi how are you? the turn signal switch is behind your steering wheel in the column.must remove horn assembly.then steering wheel,use puller to remove wheel.next remove clip that holds steel plate.(tool required).remove plate.then remove any steering column covers/plastic.then remove screws for turn signal switch.unplug wires and remove.then reinstall in reverse.

Hi...
You are looking for the location of the TURN SIGNAL FLASHER.
The turn Signal flasher on a 00 Chrysler Cirrus.
Is mounted inside of the Turn Signal switch.
Some model If you remove the steering cover you will have axces to the Flasher.
But In some Model you will need to replace the Multifuntion Switch ( Turn signal switch)

OK.. I hope this help on your question.
I'm Based on a AUtorepair Software. to give the answear..

Thank you for use fixya..