How to remove the rear light on my Freestar license plate

Remove the wheels if possible.
Remove the two clips from each side (by pulling up the center).
Move the fender liner away to access and remove the 7 mm bolt that is near the corner.
Unscrew the four cargo anchors from the floor of the trunk.
Move the trim panel and remove the 4 10mm bolts.

To get to the license plate lights assembly, you can follow these steps:

Open the rear compartment lid and locate the license plate light assembly inside the trunk lid.
Above the license plate, locate four Philips head screws holding the license plate light assembly inside the trunk lid.
Remove the screws (caution: in winter, plastic is extremely fragile and can break easily).
Once the screws are off, your license light assembly is loose inside the trunk lid.

rear bumper cover removal?? ' Cadillac Owners Forum (cadillacforums.com)

2002 escalade changing liscense plate lights ' Cadillac Owners Forum (cadillacforums.com)

copy and paste if no help the go to https://www.justanswer.com/

https://enginepartsdiagram.com/fuel-pump-inertia-switch-ford-freestar/

Not told! However, this gives a clue right here on Fixya

SOLVED: Location of fuse box for license plate light on a - Fixya

https://www.fixya.com > Forum > Cars & Trucks
Oct. 23, 2011 - location of fuse box for license plate light on a 1998 chevy cargo van - Cars & Trucks question.
1 answer · 3 votes: The license plate bulb is fed off the same fuse as the parking lights/tail lights.

Chevrolet Express (2003-2020) fuses and relays

https://fuse-box.info > chevrolet > chevrolet-express-20...
Fuse box diagram (location and assignment of electrical fuses and relays) for Chevrolet (Chevy) Express (2003, 2003, 2005, 2006, 2007, 2008, 2009, 2010, ...

There are 6 bolts that hold the rear trunk panel on the trunk itself: 4 behind the license plate on the outside of the trunk and two inside the trunk panel trim.
1. Remove the license place from the DeVille rear trunk panel.
2. Remove the 4 bolts located below the license plate.
3. Remove the trunk panel (felt) trim inside the trunk.
4. There is a small bolt on each side of inside trunk panel (4mm I believe). Remove them. Each will have a rubber washer on them so you'll know you are removing the correct bolt.
5. From the outside of the trunk, lift out the rear trunk panel. The license plate light (and reverse lights) are removed by turning the light assemblies counter clockwise.

what country? ( export below means , NOT USA)
its in the FSM
quote:
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:

1. Remove the two mounting screws from the license plate lamp.
2. Remove the license plate lamp from the rear bumper fascia.
3. Remove the license plate lamp socket by turning it counterclockwise.

To Install:

1. Install the license plate lamp socket by turning it clockwise.
2. Position the license plate lamp to the rear bumper fascia.
3. Install the license plate lamp mounting screws.

YOU HAVE TO OPEN THE TRUNK LID REMOVE THE BLACK PLASTIC COVER FOR THE TRUNK LID LATCH.REMOVE THE LICENSE PLATE LIGHT HOUSING FROM THE TRUNK LID.REMOVE THE BULB SOCKET FROM THE LICENSE PLATE LIGHT HOUSING.TO REMOVE BULB FROM THE SOCKET SIMPLY PULL IT STRAIGHT OUT OF THE SOCKET.

LICENSE PLATE LAMP BULB
REMOVAL

1. Remove screws attaching license plate lamp to rear bumper
2. Remove lamp from bumper.
3. Remove bulb socket from lamp.
4. Pull bulb from socket.

INSTALLATION

1. Install bulb into socket.
2. Install bulb socket into lamp.
3. Place lamp in position.
4. Install screws attaching license plate lamp to rear bumper.

License Plate Lights Removal & Installation License plate lamp retainer clips

To Remove:
Remove or disconnect the following:

1. License plate
2. Pin-type retainers and the luggage compartment lid trim panel
3. License plate lamp electrical connector
4. Lamp socket from the license plate lamp
5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp

To Install:

1. Install or connect the following:
2. License plate lamp
3. Lamp socket to the license plate lamp
4. Electrical connector
5. Luggage compartment lid trim panel
6. License plate

this is straight out of the book ok

1. Open the rear compartment lid.
2. Remove the rear compartment lid trim.
3. Pull back on the rear compartment trim panel.
4. Unplug the lamp connector from the rear compartment lid wiring harness.
5. Press the grommet out of the rear compartment lid.
6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
7. Remove the bulb.