2003 Jeep Grand Cherokee Logo

Related Topics:

Anonymous Posted on Oct 29, 2012

2003 jeep grand cherokee will not start.

Fuel pump and filter replaced last week. Battery, starter, cam and crank all fine.

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Master 2,101 Answers
  • Posted on Oct 30, 2012
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Oct 23, 2012
Answers
2101
Questions
1
Helped
581881
Points
6613

Does is crank but no start,and are you getting spark to thw start plugd

5 Related Answers

Anonymous

  • 218 Answers
  • Posted on Apr 28, 2009

SOURCE: 1995 JEEP GRAND CHEROKEE RAN AND DIED WILL NOT START

IS IT THE 4.0L?IF SO U MAY HAVE A BAD CRANKSHAFT POSITION SENSOR.

Ad
66 chrgr

mike loshbough

  • 1011 Answers
  • Posted on Jun 11, 2009

SOURCE: my 1997 jeep grand cherokee cuts off while driving or wont crank

the crank sensor can be bought at a autozone napa ect . but it is not very easy to replace unless you can get under the jeep!

Anonymous

  • 58 Answers
  • Posted on Jun 28, 2009

SOURCE: replace fuel filter on 1997 jeep grand cherokee

If you have the V8 engine, the filter is actually part of the fuel pump. WHICH IS IN THE TANK

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Jul 21, 2010

SOURCE: location of cam sensor 2003 jeep grand cherokee v8

Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Testimonial: "that is just what i needed thanks"

Anonymous

  • 2926 Answers
  • Posted on Aug 15, 2010

SOURCE: 96 jeep grand cherokee limited

I could be the CKP (crank sensor), but it could also be several other factors including the TPS. The correct way to start a diagnosis would be to see if any trouble codes are stored in memory. I'm assuming all basic ignition components are ok ; spark plugs, etc.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

1993 jeep grand Cherokee Larado stalling for no reason. we have looked or changed coil, fuel pump, relays, cam sensor inside distributor, this thing still stalls out, but starts right back up.

Crank sensor. Its on the passenger side on the top of tranny. Will have either 1 or 2 10mm bolts holding it on. And a plug. My 94 had the same problem. It would run fine then you shut it off and all it woild do is crank. Wait like an hour and it will start back up. New crank sensor and it was fine
0helpful
1answer

Jeep grand cherokee dies while driving

did you change the fuel filter, very common problem that gets over looked too many times
0helpful
1answer

2001 jeep grand chorkee long crank times replaced crank sensor cam sensor and fuel pump cold starts only 4.7 engine

Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.


To confirm the problem, the basic troubleshooting is required.


Click this link below and follow the troubleshooting:------

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

---------

This will help.

Thanks.

0helpful
3answers

My jeep cherokee just broke down for no reason what could it be it wont start up.

Two most common failures are crank position sensor and fuel pump however, without any details in you post, I could be way off...there are many items that can cause a no start. I suggest you get a chilton or haynes manual, a digital multi meter and do some testing. If you need additional help with what you find post back here. first thing you need to do is isolate the problem to either electrical or fuel, then work from there.
4helpful
2answers

My 1995 grand jeep cherokee won't start but It turns over an a battery jump didn't work. I believe I'ts an electical problem, maybe related to the alarm because the starter, engine and battery seem fine..?...

Alarms usually won't allow the engine to crank. If it is the alarm, arming then disarming it usually gets them to start. However, you probably aren't that lucky. Probably the most common problem for Cherokees with ignition issues is a crank sensor or a fuel pump. Listen to hear if the fuel pump runs when you turn the key to the run position (it will only run for 2 seconds, so have someone else turn the key while you listen at the gas filler neck)
0helpful
1answer

1993 Jeep Grand Cherokee will not start. When

Check your fuel pump ,fuel lines,.One of the most overlooked starting causes is fuel delivery. Find the fuel rail to the injectors. Assuming you don't have a fuel pressure gauge, remove the dust cap on the fitting on the fuel rail and press the center pin in the valve to see if there's a good amount of pressure for a very brief second. There will be no continuous pressure unless the engine is running or is being cranked over. Have somebody crank it for you for a second to see if high pressure is present.

If not, first look at the fuel cutoff switch usually located in the inside stowage compartment of the vehicle. See if the reset button clicks when you press it. Next check the fuel pump fuse and relay, and finally the pump itself could be bad.
0helpful
1answer

2001 Jeep Cherokee - Cranks won't start - Gas gauge "E" w/gas

Disconnect and replace fuel filter.With filter disconnected have someone momentarily turn key to on position to see is fuel pump is working.Make sure you have lots of rags,a drain pan and safety goggles on
0helpful
3answers

My 2003 Jeep Grand Cherokee will not start. I

Could be fuel pump. Have you changed your fuel filter?
0helpful
1answer

2003 jeep cherokee losing rpm and speed which is sporadic

Check fuel pump pressure, replace fuel filter, replace relays.
1helpful
2answers

1997 Jeep Grand Cherokee cranks but won't start

Same thing happened to me at about 140k. It was the fuel pump. Best way to test if your pump is failing and loosing pressure is to see if the car will start immediately after it has been running, or turn the key to the alt position for a few minutes before starting. If your engine fires faster after it has been running or the key has been in the alt position you will probably need a new fuel pump. Great news is with a very deep socket to get the tank straps off its a 30 minute job to replace the pump/filter assembly.
Not finding what you are looking for?

481 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...