Question about Cars & Trucks

1 Answer

Front driver seat is loose

The front driver seat brackets are loose they came apart, i am trying to find the similiar brackets for it but i have had no luck, if i cvan ifnd them or even find some that will re enforce my seat a little bit more iit would be better, ive also tried welding on new brackets but have had no luck in that department either because the seat still comes undone so it is no good at all

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,962 Answers

Go to junkie

Posted on Aug 28, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 550 Answers

SOURCE: Carpet wet behind driver seat

look for rust holes, missing drain plugs, in the floor pan, under the car, spray when driving also comes up off the road and tires, there are a number of points of entry, seat mounnts transmission mounts
not really a solution, just something to check

Posted on Oct 13, 2008

mteplitski

Max Teplitski

  • 3 Answers

SOURCE: stuck rear seat

Ok, I had similar problem on my Chevy Venture.
Step one: Lower the Back part of the seat down.
Step 2: Get a BIG flat head screw driver
Step 3: Use the screw driver to push down the Lever in the back of the Seat to unlatch the rear hooks. - You won't be able to do it by hand, not enough strength can be applied to get that rear lever to move.

Then, when you put it back in, make suure the front latches are open prior to putting the seats back in again. If they are locked, you have to open them (using the same screw driver) otherwise, you will have the same issue again.

GM Seat system for the vans sucks a$$. I've seen this problem too many times.

Posted on Jan 09, 2009

Anonymous

  • 1 Answer

SOURCE: renault espace 2.0 8v s reg

my espace runs rich and i loose power goin up a hill. its really slugish as well change all the parts that were diognoised but still have problems with it

Posted on Aug 02, 2009

Anonymous

  • 347 Answers

SOURCE: broken driver seat track bracket hinge assembly

track its self bolts on after u take the seat out turn it upside town and un bolt the track u can pick them up at any junk yard or salvage yard

Posted on Oct 09, 2009

Anonymous

  • 14 Answers

SOURCE: FRONT HEATED SEATS

you need to check the resistance in each of the heated seat elements in the seat. There's a two wire connector under the back of each front seat. The connector should be green. disconnect it and measure the resistance along the circuit going into the seat. if it isnt .1 - .3 ohms, replace the appropriate heated seat element

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know where the seat memory module is on a 2001 Buick park avenue, and how do i disconnect it?


How do you know it's the seat memory module ? It is located on the bottom of the driver seat .
Memory Seat Control Module Replacement

Raise the seat to the full upright position.
Unsnap the front track cover from the seat by sliding forward.
Remove the 2 front screws from the memory seat module bracket.
Remove the front seat anchor bolts from the rear of the seat tracks.
Raise and support the rear of the seat assembly.
Disconnect the electrical connector.
Remove the 2 rear fasteners from the bracket.
Remove the memory seat module (1) and the bracket.

Feb 06, 2017 | 2001 Buick Park Avenue

1 Answer

How to remove driver seat 300 zx


There are 4 bolts which retain the seat in place. The ones in the front, the seat bracket are bent in an L shape, so you reach them by takeing a 14mm socket, short extension and ratchet and to the outer side if the seat running from front to back, you will see the bolt on the left and one on the right,.Bring the seat all the way back to make ot easy to reach and then you can remove them. Now slide the seat all the way to the front. Most ofen there is a plastic cover over each bolt. Carefully pry one side off and the cover will come off. Below the covers are two more 14mm bolts When you remove them, position the seat as forward as you can to make access easy to the bolts. the seat is loose from the car. NOTE: I got a head of my self. The rear bolts should bee removed first then remove the front bolts are removed. Additionally, Position the seat in a semi reclined position so that it will be easy to take out of the car. If these are electric, there will be connectors under the seat which must be disconnected. In the middle of the connecter where they plug in, there should be a little lever looking part on the center of the outside connector which you must depress while pulling the connectors apart I hope I haven't been too confusing. I have Parknison's disease and although I am a Nissan Master tech, the disease can sometimes affect my thought train. I have read and reread what I have written to you and am satisfied that it shouldn't be confusing and you'll be able to get the seat out just fine.
Good luck

Jun 28, 2014 | 1986 Nissan 300ZX

2 Answers

How to remove studs from audi seat bracket


Perhaps a grinder will do it .

Feb 23, 2018 | 2003 Audi A4

2 Answers

Drivers seat how do i take it out 2005 malibu drivers seat is sagging on the right rear


pry off any plastic bolt covers where the bolts secure the seat
pull 4 bolts securing seat to vehicles floor pan
Disconnect negative battery teminal,
disconnect any electrical plugs going to the seat
pull out drivers door opening

Aug 19, 2010 | 2005 Chevrolet Malibu

1 Answer

Where is the flasher relay on a 92 Subaru Loyale wagon?


Front seating area, driver side, under dash, above brake pedal, mounted in steering column support bracket

i hope this helps you

Apr 10, 2010 | Subaru Loyale Cars & Trucks

2 Answers

2004 Malibu with broken weld on seat motor


you will have to replace the complete assy. the cheapest way is look for a complete wrecking yard seat, or have yours welded at a local machine shop

Jan 08, 2010 | 2004 Chevrolet Malibu

1 Answer

Need to replace front drivers seat electric


4 bolts hold it to the floor ,unplug the multiplug connectors ,thats it .Then keep overweight people from sitting on it

Dec 12, 2009 | 1992 Buick Roadmaster

2 Answers

Stuck rear seat


Ok, I had similar problem on my Chevy Venture.
Step one: Lower the Back part of the seat down.
Step 2: Get a BIG flat head screw driver
Step 3: Use the screw driver to push down the Lever in the back of the Seat to unlatch the rear hooks. - You won't be able to do it by hand, not enough strength can be applied to get that rear lever to move.

Then, when you put it back in, make suure the front latches are open prior to putting the seats back in again. If they are locked, you have to open them (using the same screw driver) otherwise, you will have the same issue again.

GM Seat system for the vans sucks a$$. I've seen this problem too many times.

Dec 04, 2008 | 2002 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...