My rear wipers, rear washer and rear defrost stopped working. I have changed the fuses. what else would cause these 3 to stop?

[PDF]Wiring Diagram.pdf - Ken Gilbert

ken-gilbert.com/wrx/mans/99.../Wiring%20Diagram.pdf

Each connector number shown in the wiring dia- ... Rear defogger cord (Ground). Fuel tank cord,. Roof cord, ... circuit. Then check the switch, relay, fuse, ground, etc. 4. .....Rear wiper motor. Rear wiper ... License plate light RH. Tail light LH.

#? license plate light - Circuit Wiring Diagrams

circuitswiring.com/tag/license-plate-light/

2008 Volkswagen Newbeetle Main Fuse Box Diagram 2008 Volkswagen Newbeetle ...Parts: rear window defogger, shift lock, battery positive voltage, interior light, A/C clutch, ... brake light, daytime driving light, wiper and washer system, vacan, fuel pump, central ... 1997 Suzuki Geo Tracker Left Dash Fuse Box Diagram.

#? license plate light - Circuit Wiring Diagrams - Page 3

circuitswiring.com/tag/license-plate-light/page/3/

Audi A4 Engine Fuse Box Diagram Audi A4 Engine Fuse Box Map Fuse Panel ... mirror control, wiper, washer, horn, brake light, cruise control, heated rear window, ... 2003Suzuki Aerio Dash Fuse Box Diagram 2003 Suzuki Aerio Dash Fuse Box ... rear defroster, fuel injection controller, radio, A/T controller, hazard light, ...

The only thing they have in common is the ignition switch.

Sounds silly but if you go to google translate on the internet, you can work out what each Japanese word translates to. It may help, or alternatively, you will need to pull out 1 fuse at a time until the wiper stops. It will probably be a low amperage fuse. Not one of the large ones. Check that nothing else has turned off when you pull the fuse. It will stop your wiper but it may also cause some of the other electrical items to turn off as well such as your radio, washers, front wipers etc. Make sure these still work. If not, you may have to disconnect the wiring from the rear wiper motor which will eman you have to get inside the rear panel to access it.

FUSE...RELAY...CIRCUIT BREAKER...OR WIRING! WITH REAR WIPER SQUITER SWITCH ENGAGED,,,CHECK FOR VOLTAGE AT HARNESS CONNECTOR

Tried pulling the fuse for the washer fluid? Sounds like the wiper motor is failing or it doesn't have a good connection. Disconnect the battery at night to ensure you'll have enough power to crank it in the morning.

The fuse for the rear wiper is located in the interior fuse panel on the passenger door side of the dash. It is the 3rd one down from the top in the left column (#3) and it is a 15 amp.

If your rear wiper, fluid wash, and rear defrost stopped working at the same time try this first before taking it to the dealer. Start the 4Runner and lower the rear window glass. Wait a few seconds and raise the rear window. Turn the engine off and wait a few seconds. Restart the engine and see if this helps. I had the same problem after I had my drive belt replaced and the shop disconnected the battery cable. When the battery cable is disconnected it causes the rear wiper, fluid wash and defrost to stop working. Good luck!

sounds like a blown fuse. looke and the fuses under the drivers side dash by your left knee. there are also fuses under the hood.
www.3si.org and www.stealth316.org are two very helpful sites for the 3000gt.

You are very welcome. Glad to help.
The graciousness of a FixYa rating for my assistance would be greatly appreciated.
Thanks for choosing FixYa to solve your problem!

Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------

• The wipers stay on continuously — rear wiper

• Circuit.
• Rear wiper/washer switch.

• GO to Pinpoint Test L .

---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.

• Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?

Yes GO to L2 .
No INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.

• Is the resistance greater than 10,000 ohms?

Yes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
No REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.