How do you find the radio code for a 1994 mercedes benz s500

SOURCE: Need Radio Code for CLK430 Mercedes Benz

Yes. Every time you disconnect the batterie you need to put radio code again.

SOURCE: c280 radio code

THE CODE SHOULD BE IN YOU'RE MANUAL. IF NOT GO TO THE DEALER W/ YOUR VIN, ENTER THE CODE AND PUSH SCAN

mx5turbo92

• 545 Answers
• Posted on Dec 17, 2009

SOURCE: i need the mercedes benz 1999 clk 430 radio code

AR82.60-P-7502-01A Coding Radio
(MODEL all with CODE (750) Radio Becker Europa 2000 with CODE (751) Radio Becker Grand Prix 2000 with RDS)

1. If the radio is disconnected from the power supply, it is not operational when re-connected. After switching on the ignition and the radio, the readout CODE appears in the display.
2. The code number for the radio is advised to you on the enclosed CODE CARD.
3. To enter the first digit of the code number, you have to continue pressing station button 1 until the correct digit appears in the display. Adopt the same procedure for the second, third and fourth digits.
4. Once you have entered the correct code number with the station buttons 1, 2, 3, 4 and confirmed the entry with the SEEK button (press down), the readout CODE disappears. The radio can now be operated.
5. If you enter a wrong code three times, you must wait 15 minutes before making a new entry. In addition, if 9 incorrect entries are made, the radio will then not operate for 24 hours. During this time the radio and the ignition (terminal 15) must remain switched on.

1. If the radio is disconnected from the power supply, it cannot be operated by simply reconnecting. After switching on the ignition and the radio the word "CODE" appears in the display on the radio.
2. The code number for the radio is given on the enclosed CODE CARD.
3. Enter the code number with the station button, e.g. number 1, station button 1. After entering the first number the word "CODE" disappears and the number entered appears followed by 4 dashes. The next character to be entered flashes. After entering all five numbers, the first character starts flashing again. In this state the code number can be written over as frequently as desired. A correction can be made only by entering the complete code number again.
4. Confirm code number: Press TUNE, AUTO/SEEK or SC button. The radio automatically switches on and indicates the radio station or frequency stored with station button 1.
5. If an incorrect code number is entered and confirmed, the word "CODE" appears again on the display. If an incorrect code is entered three times the word "WAIT" appears on the display and the radio locks up for approx. 10 min. If the code is entered incorrectly three times again the radio locks up again for 10 min. Three more incorrect entries (a total of 9 incorrect attempts) increase the lock-up time to 60 min. Another three incorrect entries lock up the radio for another 60 min. The waiting time runs only when the radio is switched on.

SOURCE: how to reset airbag for mercedes benz c220 1994

This can not be reset by conventional methods. This must be done through a scan tool. Usually only the dealer scan tool will communicate with the SRS module. If the SRS light is on you have other issues and they must be remedied before the light will go out. There is no way of knowing what the issue is without running codes with the scan tool.

SOURCE: where are the fuse boxes located ofr my 2002

A 2002 S500 actually has 3 differant fuse boxes.
2 of them are located under the engine hood, they are both against the firewall in the back corners of the engine compartment. The fuse box on the drivers side of the firewall has most of the common fuses in it.
The last one is located under the rear seat. There is a access panel below the passengers side rear seat, just unclip the plastic panel from the top.
Fuse chart can be found in the rear with the spare tire tools.
This will help. Thanks please keep updated.please please do rate the solution positively .thank you for using fixya