Replaced cylinder heads but now cant seem to set idle veh runs good but wont idle and stalls
SOURCE: torque settings for cylinder head nissan sentra
Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees
SOURCE: nissa pickup wont idle at all
Here are the most common causes of surges, stalls at stops, low erratic idle speed and stall, rough idle and engine hesitation, it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.
SOURCE: 2000 nissan xterra hesitating when engine is warm
We are having the same problem. We are right now changing the crankshaft position sensor along with the intake and manifold gaskets.
SOURCE: 87 nissan starts then stalls
jdmbaker: There are a few areas I would suggest looking in.
First, I would be looking for a false air problem. This is a condition where you have un-metered air getting into the engine. A torn airflow meter boot, or large vacuum leak such as a split pcv hose.
Second, your injector pulse width is primarily dependent on the coolant temperature sensor. This component is located at the front of the motor just below the thermostat housing. The sensor gives the ECM resistance values based on the temperature of the coolant. If the sensor fails, usually, they have a tendency to create a lean condition. This shortens the pulse width of the injectors which essentially starves the engine for fuel. One way you can perform a quick test for a lean condition, is to pinch off the return hose for the fuel going to the tank. If you look at the fuel hoses, they run right next to each other. You have one which comes from the fuel filter. That is the feed line. Pinch the other hose. This will boost the fuel pressure causing more fuel to be sprayed out of the injectors.With the hose pinched, hit the throttle, if the engine will rev up, you persue the lean condition theory.
Third. Check for a weak spark. A severely worn cap and rotor or bad plug wires can cause a hesitation and stalling problem if they are bad enough.
Fourth. The air flow meter could be faulty. This is a very common symptom matching you description.
Odds are that one of these are the solution. Good luck and let me know how you do.
SOURCE: My 1986 Nissan 300zx non-turbo was running fine,
It sounds like the number 2 injector is hung open.
It will dump fuel and cause all sorts off issues with the ECU.
You should ohm that injector and compare it with the others to see if it is wildly different. If so, change it out and retest.
It can be issue
with IAC( idle air control valve) causing the problem.
There
are many other possibilities causing these idle issues. Engine idles rough.
There
are few help links with solutions to troubleshoot such idle issues.
I
suggest you refer the link below and follow
its troubleshooting details:------
Click
the link below:-----
-----------
http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html
------------
http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html
---------
http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html
------------------
http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html
-----------
Cold start problem and vehicle shudder around 2500 to
3500 rpms
----------
http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html
-----------
http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html
--------
http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html
-------------
http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html
------------
http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html
-----------
http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html
---------
High
Idle Problem
http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html
-------
http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html
---------
http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html
--------
http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html
-------
http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html
----------
http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html
-----------
http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html
---------
These
details will help.
Thanks.
1,396 views
Usually answered in minutes!
×