The black door trim on the bottom edge of the front doors

Start by removing inside door handle screw cover + screw.
Then remove upper door trim screw, rear upper corner.
Then front lower screw, bottom rear corner.
Next, center trim screw, above map pocket.
Then you are ready to pull the front of door trim straight out. It has pin type retainers that will release when pulled. It would help if you have a plastic trim pry tool. If not just put your fingers under edge of trim and pull.
Then you disconnect the electrical connectors. To remove panel.

Remove the door trim panel as follows:

• Insert a flat-bladed tool behind the forward edge of the door handle bezel.
  
• Gently pry the bezel away from the door trim panel and disconnect the electrical connector.
  
• Remove the armrest cover plate by inserting a small flat-bladed tool into the rectangular hole until it bottoms out and tilting the tool forward in order to release the locking tab.
  
• Remove the fasteners from the armrest.
  
• Remove the courtesy lamp assembly.
  
• Remove the fastener from behind the lamp assembly.
  
• Remove the push-in retainer from the defroster duct.
  
• Lift straight up on the trim panel in order to disengage the hooks on the backside of the panel.
  
• Disconnect the electrical connectors.
  

Removing the door handle bezel

Removing the armrest cover plate

Door trim panel detail view

1. Install the door trim panel as follows:
2. Connect the electrical connectors.
   

• Install the clips on the electrical harness to the front door control module.
  
• Engage the lower hooks on the door trim panel into the slots in the door.
  
• Align the remaining hooks to the slots in the door.
  
• Push the door trim panel downwards in order to fully seat the hooks into the door.
  
• Ensure that the door trim panel is fully seated prior to fastener installation.
  
• Install the push-in retainer in the defroster duct.
  
• Install the fastener in the courtesy lamp opening. Tighten the fastener to 5 inch lbs. (0.6 Nm).
  
• Install the courtesy lamp assembly.
  
• Install the fasteners in the armrest. Tighten the 2 fasteners to 5 inch lbs. (0.6 Nm).
  
• Install the armrest cover plate.
  
• Install the inside door handle bezel.
  

Did you find the one inside the door pull cup ?
Remove the push pin rivet on the upper rear edge of the trim panel and the screw at the upper front edge near the mirror.
Remove the trim panel fasteners at the pull cup and lower the rear corner of the trim panel.
Pull up on the door trim panel assembly to disengage the trim panel to door structure attaching hooks and remove the door trim panel.
Did you try watching a video on youtube ?

Like reference guide, check this procedure to Removal & Installation / Door Lock Motor...

The door lock motor is integral with the door latch. If the door lock motor is found to be defective, the entire door latch must be replaced.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Roll the door glass down.
3. Disengage the 2 clips attaching the speaker grille to the door trim panel. (They are at the front of the grille, one near the top, and the other one at the bottom).
4. Remove the 3 large washer-headed screws surrounding the speaker.
   
   
   Fig. Fastener location for the door lower trim panel
   
5. Remove the access cover at the front of the door trim panel. Remove by prying at its rear edge.
6. Remove the red courtesy reflector from the lower tail of door. Disengage by prying at the screwdriver notch at the bottom of the reflector.
7. Remove the flag trim panel from the door by prying it off at the 2 attachment clip points.
8. Remove the 7 screws attaching the door trim panel to door:
   1. One screw is located at the lower rear screw pocket.
   2. Three screws are located along the bottom of the door.
   3. One screw is located inside the handle opening.
   4. One screw is located at the upper front.
   5. One screw is in the pull cup.
      
9. Disengage the 2 hidden clips attaching the rear of the trim panel; pry them off at the 2 attachment clip points.
10. Lift the trim panel upward and away from the door, disengage the trim panel from the upper retainer channel.
11. Disengage the clip attaching the latch linkage to back door handle.
12. Disconnect the electrical connectors as necessary, including the lower foot light, if equipped.
13. Remove the door trim panel from the door.
14. Remove the water shield (water dam) from the inside of the door.
    
    
    Fig. Remove the flag trim panel, door trim access cover, inside remote handle, and power door lock switch
    
15. Raise the door glass.
16. Remove the bolt and nut for the rear glass run channel and position the channel aside.
17. Disconnect the lock rod from the lock button bellcrank.
18. Disengage the lock and latch rods from the clips on the inner door panel.
19. Disconnect the lock and latch rods from the outside door handle and the key cylinder at the door latch.
20. Disconnect the wire connector from the power door lock motor.
21. Remove the screws attaching the door latch to the door end frame.
22. Remove the door latch and the power door lock motor from the vehicle.
    
    
    Fig. Expanded view of the door lock, latch, and linkage
    
    
    
    Fig. View of the door lock button, latch rod, lock rod, and door latch
    

Hope helps (remember rated this).

Very easy! One tool that will save you a lot of headache and anger can be bought at any auto parts store and looks like this:



You use this tool to pop loose the plastic fastners that are attached to the door panel edges.

But first, remove all screws...remove the door handle cup, pop loose the master door/window stich assmbly, etc. Very simple process....takes less than 10 minutes.

Door Panel

1. Remove all door inside handles.
   
2. Remove the door inside locking rod knob.
   
3. On styles with door pull handles, remove the screws inserted through the handle into the door panel.
   
4. On styles with remote control mirror assemblies, remove the remote mirror escutcheon and disengage the end of the mirror control cable from the escutcheon.
   
5. On styles equipped with switch cover plate in the door armrest, remove the screws securing the cover plate, then disconnect the switches and cigar lighter, if so equipped, from the harness connectors.
   
6. Remove the remote control cover plates and remove the exposed screws securing the cover plate to the door inner panel.
   
7. On styles with integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. On some styles it may be necessary to remove the screws behind the armrest deflector or courtesy lamp remote control cover plate. On styles with armrest applied after the door trim installation, remove the armrest to door inner panel attaching screws.
   
8. On styles with with two piece trim panels, disengage the retainer clips at the front and rear of the upper trim panel. Remove the upper trim panel by lifting upward and sliding slightly rearward to disengage the the front door inner panel at the beltline.
   
9. On styles with electric switches located in the door trim panel, disconnect the wire harness at the switch assembly.
   
10. To remove the lower trim panel, remove the attaching screws along the upper edge of the lower trim panel. Then starting at a lower corner, insert a pry type tool between the door inner panel and the trim panel and disengage the retaining clips down both sides and across the bottom. On styles with courtesy lamps or reading lamps located in the trim panel, disconnect the wire harness at the lamp assembly.
    
11. On styles with one piece trim panels, remove all the clips around the perimeter of the trim panel. Push the trim panel downward and outboard to disengage it from the door inner panel at the beltline. Disconnect any courtesy lamp wire harnesses, if so equipped and remove the trim panel from the door.
    
12. Installation is the reverse of removal. On styles with adjustable trim supports at the beltline, the door trim panel can be adjusted in or out so as not to restrict door window operation
    

PLEASE DON'T FORGET TO RATE!!

Door Panel

1. Remove the door handles and the locking knob from the inside of the doors.
   

If equipped with screw retained door pull handles, remove the screws through the handle into the door inner panel.

1. If equipped with remote control mirrors, remove the remote mirror escutcheon, then disengage the end of the mirror control cable from the escutcheon.
   

Door lock remote control handle


Removing the clip from inside the door handle

3. If equipped with a switch cover plate in the door armrest, remove the cover plate screws, then disconnect the switches and the cigar lighter (if equipped) from the electrical harness.
4. If equipped with an integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. If equipped with an armrest applied after the door trim installation, remove the armrest-to-inner panel screws.


View of the armrest switch cover plate and remove mirror cable attachment

1. If equipped with two-piece trim panels, disengage the retainer clips from the front and the rear of the upper trim panel, using tool No. BT-7323A, then lift the upper door trim and slide it slightly rearward to disengage it from the door inner panel at the beltline.
   

If equipped with electric switches in the door trim panel, disengage the electrical connectors from the switch assembly.

1. Along the upper edge of the lower trim panel, remove the mounting screws. At the lower edge of the panel, insert tool No. BT-7323A between the inner panel and the trim panel, then disengage the retaining clips from around the outer perimeter. To remove the lower panel, push the panel down and outward to disengage it from the door.
   

If equipped with courtesy lights, disconnect the wiring harness.

1. If equipped with an insulator pad glued to the door inner panel, remove the pad (with a putty knife) by separating it from the inner panel.
   

To install:
If replacing the inner pad to the door inner panel, use 3M General Trim Adhesive No. 8080, glue it to the panel.

1. If removed, glue a new inner pad to the door inner panel.
   

If equipped with courtesy lights, connect the wiring harness.


Exploded view of the window regulator handle


Exploded view of the door trim panel

1. Engage the retaining clips around the edge of the lower trim panel, then install mounting screws.
   

If equipped with electric switches in the door trim panel, engage the electrical connectors to the switch assembly.

1. If equipped with two-piece trim panels, engage the retainer clips to the front and the rear of the upper trim panel.
   
2. If equipped with an integral armrest, install the retaining screws.
   
3. If equipped with a switch cover plate in the door armrest, engage the switches and cigar lighter (if equipped) harness connectors, then install the cover plate and secure using the plate screws.
   
4. If equipped with remote control mirrors, engage the control cable, then install the remote mirror escutcheon.
   

If equipped, install the pull handle screws through the handle into the door inner panel.

1. Install the door handles and the locking knob to the inside of the doors.
   

Exploded view of the 2-piece door trim

1. Remove the door handles and the locking knob from the inside of the doors.
   

If equipped with screw retained door pull handles, remove the screws through the handle into the door inner panel.

1. If equipped with a switch cover plate in the door armrest, remove the cover plate screws, then disconnect the switch
   

from the electrical harness.

1. If equipped with an integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. If equipped with an armrest applied after the door trim installation, remove the armrest-to-inner panel screws.
   
2. If equipped with two-piece trim panels, disengage the retainer clips from the front and the rear of the upper trim panel, using tool No. BT-7323A, then lift the upper door trim and slide it slightly rearward to disengage it from the door inner panel at the beltline.
   

If equipped with electric switches in the door trim panel, disengage the electrical connectors from the switch assembly.

1. Along the upper edge of the lower trim panel, remove the mounting screws. At the lower edge of the panel, insert tool No. BT-7323A between the inner panel and the trim panel, then disengage the retaining clips from around the outer perimeter. To remove the lower panel, push the panel down and outward to disengage it from the door.
   

If equipped with courtesy lights, disconnect the wiring harness.

1. If equipped with an insulator pad glued to the door inner panel, remove the pad (with a putty knife) by separating it from the inner panel.
   

To install:
If replacing the inner pad to the door inner panel, use 3M General Trim Adhesive No. 8080, glue it to the panel.

1. If removed, glue a new inner pad to the door inner panel.
   

If equipped with courtesy lights, connect the wiring harness.

1. Engage the retaining clips around the edge of the lower trim panel, then install mounting screws.
   

If equipped with electric switches in the door trim panel, engage the electrical connectors to the switch assembly.

1. If equipped with two-piece trim panels, engage the retainer clips to the front and the rear of the upper trim panel.
   
2. If equipped with an integral armrest, install the retaining screws.
   
3. If equipped with a switch cover plate in the door armrest, engage the switch harness connector, then install the cover plate and secure using the plate screws.
   

If equipped, install the pull handle screws through the handle into the door inner panel.

1. Install the door handles and the locking knob to the inside of the doors.
   

1. Remove the front door trim panel handle bezel cover.

1. Remove the front door trim panel handle bezel screws.

1. Remove the front door trim panel lower screws.

NOTICE: To avoid damaging the front door trim panel, do not pull the bottom of the panel outward.

1. Remove the front door trim panel by lifting upward on the armrest to disengage the panel clips.

1. Disconnect the electrical connectors.

1. Disconnect the lock rod cable from the front door trim panel.

1. Disconnect the door handle conduit and cable from the front door trim panel.

1. To install, reverse the removal procedure.

be patient during these procedures to not damage the trim panel...they cost $150>275 ec........GL hope this helps

The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps

1. Remove all door inside handles.
2. Remove the door inside locking rod knob.
3. On styles with door pull handles, remove the screws inserted through the handle into the door panel.
4. On styles with remote control mirror assemblies, remove the remote mirror escutcheon and disengage the end of the mirror control cable from the escutcheon.
5. On styles equipped with switch cover plate in the door armrest, remove the screws securing the cover plate, then disconnect the switches and cigar lighter, if so equipped, from the harness connectors.
6. Remove the remote control cover plates and remove the exposed screws securing the cover plate to the door inner panel.
7. On styles with integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. On some styles it may be necessary to remove the screws behind the armrest deflector or courtesy lamp remote control cover plate. On styles with armrest applied after the door trim installation, remove the armrest to door inner panel attaching screws.
8. On styles with with two piece trim panels, disengage the retainer clips at the front and rear of the upper trim panel. Remove the upper trim panel by lifting upward and sliding slightly rearward to disengage the the front door inner panel at the beltline.
9. On styles with electric switches located in the door trim panel, disconnect the wire harness at the switch assembly.
10. To remove the lower trim panel, remove the attaching screws along the upper edge of the lower trim panel. Then starting at a lower corner, insert a pry type tool between the door inner panel and the trim panel and disengage the retaining clips down both sides and across the bottom. On styles with courtesy lamps or reading lamps located in the trim panel, disconnect the wire harness at the lamp assembly.
11. On styles with one piece trim panels, remove all the clips around the perimeter of the trim panel. Push the trim panel downward and outboard to disengage it from the door inner panel at the beltline. Disconnect any courtesy lamp wire harnesses, if so equipped and remove the trim panel from the door.
12. Installation is the reverse of removal. On styles with adjustable trim supports at the beltline, the door trim panel can be adjusted in or out so as not to restrict door window operation.