Parking brake adjustment 1998 landcruiser

Here is how I adjusted my parking brakes:
Jack rear of car up and place on jackstands (safety first) Take the rear wheel off, observe how freely rotor turns while turning by hand.
Align one of the lug bolt holes with the adjusting wheel inside. Mine was at alignied with one of the holes at the 2 o'clock position. Hold a flashlight into the hole to see what the tooth of the wheel inside looks like and insert a flat blade screwdriverthrough the hole and catch beetween 2 teeth.Start moving the screwdriver handle upward (tip of the screwdriver moving downward)to turn the adjusting wheel clockwise, do about 2 turns and turn the rotor to see if there is a slight resistance turning the rotors and adjust more or less depending on the resistance.You only want some slight resistance to much and it will drag all the time and wear out your parking brake pads prematurely

Hello! See the link below with a complete video of "79 series" Landcrusier brake adjustment...The emergency brake adjustment is done (for the most part) at the rear wheels...There is an adjustment nut under the Shift Boot...If you remove the cup holder screw and slide cup holder forward you can gain access to the nut...But this is more of a "fine" adjustment...Follow the steps in the included video...when completed, drive the vehicle a 1/4 mile with the e-brake on...Then release...There should be about 5-6 clicks on the e-brake lever when completed...Guru...Saailer


http://www.youtube.com/watch?v=3w_X8rN8-Wk

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

1. Raise and safely support the vehicle.
2. Remove the rear wheel(s).
3. Release the parking brake.
4. Remove the parking brake lever cover screws and loosen the brake cable locking nut.
5. Install 2, 8mm bolts into the brake drum holes and uniformly tighten each bolt. Tighten each bolt until the brake drum is removed from the vehicle. If there is difficulty in removing the drum, insert a small tool through the hole in the rear of the backing plate, and hold the automatic adjusting lever away from the adjuster. Using another narrow, flat tool at the same time, reduce the brake shoe adjuster by turning the adjusting wheel.
   

If the drum is difficult to pull off using the bolts mentioned above, the parking brake is most likely the cause and will have to be adjusted "IN" to prevent drum to shoe contact.

Adjustment

1. Place parking brake lever in -full released- position.
2. Raise and support vehicle.
3. Remove plug in parking brake shoe support to access adjuster star-wheel.
4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
   1. Left brake - Rotate star-wheel toward rear of vehicle.
   2. Right brake - Rotate star-wheel toward front of vehicle.
5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
6. Back off adjuster six detents (teeth).
7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
8. Install access plug.
9. Adjust opposite wheel parking brake shoes using same method.
10. Lower vehicle.
11. Apply and release parking brake lever once to ensure proper operation of parking brakes.

Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

1. Lock out automatic adjuster in parking brake lever.
2. Raise and support vehicle.
3. Access and remove rear hub and bearing.
4. Remove parking brake cable bolt at knuckle.
5. Completely back off parking brake shoe adjustment.
6. Remove parking brake shoe adjuster spring.
7. Remove shoe adjuster.
8. Remove upper brake shoe hold-down clip and pin.
9. Remove lower brake shoe hold-down clip and pin.
10. Remove upper and lower shoes with return spring from shoe actuator.
11. Remove return spring from shoes.
    
    

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)
    

To install:

1. Install return spring between upper and lower shoes.
   NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
5. Install shoe adjuster. Place end of adjuster with star wheel upward.
6. Install parking brake shoe adjuster spring.
7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
9. Place Gauge over parking brake shoes at widest point.
10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
12. Lower vehicle.
13. Unlock automatic adjuster in parking brake lever.
14. Perform final adjustment of parking brake shoes

15. 
    Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.
    

    
    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
       1. Remove cotter pin, nut lock and spring washer from half shaft.
       2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.
       
       

       Fig. Hub assembly
       

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.
       
       
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.
        
        

        Fig. Rear hub and bearing mounting bolts
        

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
        
        
    To install:
    
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
       1. Install washer and hub nut on end of half shaft.
       2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
       3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).
    
    
    

    
    
    

How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:

• Remove the rear disc brake rotor.

• Remove the outboard return spring.

• Remove the adjusting screw spring.

• Remove the rear brake shoe hold-down spring and pin.

• Remove the brake shoe adjusting screw and nut.

• Remove the front brake shoe hold-down spring and pin.

• Remove both parking brake shoes and the inboard return spring.

• Check the parking brake lever for excessive wear and replace as necessary.

To install:

• Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.

• Install the rear parking brake shoe with the inboard return spring.

• Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.

• Install the brake shoe adjuster spring.

• Install the outboard return spring.

• Adjust the parking brake shoes and install the rotor, caliper and wheel.

• Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).

ADJUSTMENT

• Measure the inside of the drum portion of the rear brake rotor

• Remove the rear disc brake rotor.

• Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.

• Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size

• Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.

• Install the rear disc brake rotor.

Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

If the car has a center console between the seats, and the e-brake lever is there, remove the console there should be a bolt to tighten or loosen. Loosen it with the lever DOWN, pull the cable as tight as it will go with your hand and a pair of pliers. Holding the cable in place tighten the bolt or nut that secures the cable. If this doesn't fix it, have your rear brakes inspected and/or adjusted.

the adjustment is inside the passenger compartment. will give you the instructions i have:
1. fully release the brake lever
2. pull the parking brake lever with normal effort. maximum travel should be 6 to 8 clicks
3.remove the console and adjust the cable length by turning the nut on the equalizer
4.recheck the parking brake stroke and adjust the stroke as necessary
5.loosen the parking brake switch mounting bolt. adjust the switch so that when the lever is fully released, the switch lamp goes out, and when the lever is pulled one click the switch lamp illuminates.
6.if the switch does not operate as described, check the switch lamp bulb. if the bulb is good, replace the switch.
7. after the adjustment make sure that the rear brakes do not drag when the parking brake lever is released.
8. install the console
hope that helps

Drum, Rear Brake System Standard Rear Brake

Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake

Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:

• Have internal shoes that expand against the brake drum (1126).
• Are a single-anchor type.
• Are actuated by one rear wheel cylinder (2262).
• Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
• Adjust rear brake shoes and linings (2200) automatically.
• Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.

When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.

1. Raise and support rear of vehicle, then remove wheel and tire assembly.
2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
   1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
   2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
   3. On 2WD T100 models, proceed as follows:
   1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
   2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
   1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
   2. Remove adjusting lever spring, then the adjuster from front shoe.
   Inspection
   
   1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      
      1. On 2WD T100 models, proceed as follows:
      1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
      2. Assemble and install wheel cylinder.
      3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Backing plate and brake shoe contact points.
      2. Anchor plate and brake shoe contact points.
      3. Adjusting bolt.
      4. Adjuster and brake shoe contact points.
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
      1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
         1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
         2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
         3. Install tension spring.
         1. Ensure proper parking brake travel.
         2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
         3. Adjust strut to shortest possible length, then install drum.
         4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS

1. Remove caliper.
2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
5. Remove free wheel hub body and gasket.
6. Remove locknut, lock washer and adjusting nut.
7. Remove axle hub and brake disc as an assembly.
8. Remove oil seal and inner bearing from hub.
9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.

1. Raise and support front of vehicle, then remove tire and wheel assembly.
2. Remove clip and hole pins, Fig. 9.
3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
4. Lubricate caliper housing with suitable brake grease at pad contact points.
5. Reverse procedure to install.

The cable for the park brake is adjustable, you must jack the car up, the adjuster is on the drivers side.