Need power steering belt diagram for ford puma

https://www.google.com/search?sxsrf=ALeKk02lTsKtC4FkaLXPemOsjccehu7hhg:1585762938820&q=routing+diagram+for+a+serpentine+belt+for+a+4-cylinder,+93+Ford+Ranger.+The+Ranger+has+A/C+and+power+steering.+Thank+you&tbm=isch&source=univ&sa=X&ved=2ahUKEwjj9qml48foAhWSERQKHQ8uC_gQsAR6BAgEEAE&biw=1473&bih=696

try this link.
diagram of 2001 Ford Courier alternator belt and power steering belt...

Single belt or multipoint belt?

Power Steering Pump
See Figures 9, 10, 11 and 12

1. Remove the air cleaner intake tube and air cleaner assembly.
2. Loosen the power steering pump bolt and the adjustment locknut. Make sure the belt is properly seated on the pulley before adjustment.
   1. Turn the adjustment bolt to set the belt tension.
   2. Use Rotunda offset belt tension gauge 021-0028A, or equivalent, and following the tool manufacturers instructions, adjust the belt to the following specifications:
      
      New belt: 110-132 lbs. (50-60 kg). Run the engine for 10 minutes, then readjust the tension to 110-132 lbs. (50-60 kg). Used belt: 95-110 lbs. (43-50 kg).
      
   3. Tighten the power steering pump bolt to 27-38 ft. lbs. (37-52 Nm).
   4. Tighten the adjustment locknut to 14-19 ft. lbs. (19-25 Nm).
   5. Install the air cleaner and intake tube.

   

   

   
   

Belt Installation, Aerostar 4.0L Engine





Item Part Number Description 1 8620 Drive Belt 2 N606068 Bolt 3 10300 Generator 4 10153 Generator Mounting Bracket 5 8509 Water Pump Pulley 6 6B209 Drive Belt Tensioner 7 N800199 Screw 8 8678 Belt Idler Pulley 9 N802096 Screw 10 19703 A/C Compressor 11 2882 A/C Compressor Mounting Bracket 12 3C718 Brace 13 N806020 Bolt 14 3A674 Power Steering Pump 15 3A733 Power Steering Pump Pulley 16 N800199 Screw 17 N606572 Bolt 18 N620481 Nut 19 8501 Water Pump 20 6312 Crankshaft Pulley A - Belt Tension Check (See Specifications) B - Tighten to 40-55 Nm
(30-41 Lb-Ft) C - Tighten to 24-30 Nm
(18-23 Lb-Ft) D - Tighten to 21-29 Nm
(15-21 Lb-Ft) E - Tighten to 40-50 Nm
(30-37 Lb-Ft)

Belt Installation, Ranger and Explorer 4.0L Engine





Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 8678 Belt Idler Pulley 4 19703 A/C Compressor 5 3A733 Power Steering Pump Pulley 6 8501 Water Pump 7 6312 Crankshaft Pulley 8 6B209 Drive Belt Tensioner 9 N806020 Bolt 10 2882 A/C Compressor Mounting Bracket 11 3A674 Power Steering Pump 12 N606572-S2 Bolt 13 N800199-S8M Bolt 14 N620481-S2 Nut 15 3C718 Brace 16 N606068 Bolt 17 10153 Generator Mounting Bracket 18 8509 Water Pump Pulley 19 N605805-S2 Bolt A - Belt Tension Check (See Specifications) B - Tighten to 21-29 Nm
(15-21 Lb-Ft) C - Tighten to 40-55 Nm
(30-41 Lb-Ft)

Belt Installation, Ranger 2.3L Engine





Item Part Number Description 1 8678 Belt Idler Pulley 2 10300 Generator 3 8509 Water Pump Pulley 4 3A733 Power Steering Pump Pulley 5 2E884 A/C Clutch Pulley 6 6312 Crankshaft Pulley

Belt Installation, Aerostar 3.0L Engine





Item Part Number Description 1 10300 Generator 2 3F671 Belt Idler Pulley 3 3A733 Power Steering Pump Pulley 4 6B209 Drive Belt Tensioner 5 6312 Crankshaft Pulley 6 8509 Water Pump Pulley 7 19703 A/C Compressor

Crankshaft Belt Pulley 85 ft.lb


Rear crankshaft oil seal carrier 15 ft.lb
Camshaft Timing Belt Pulleys 50 ft.lb

Camshaft timing belt pulleys 50 ft.lb

Same TIGHTENING Sequence for Single OHC

The tensioner is between the a/c compressor and crank pulley, below the power steering pump. Use a 13 mm wrench to 'tighten' the bolt in the center of the pulley and it'll move to release tension off the belt.

try "autozone.com" for a diagram of the belts and where the tensioner is located to tighten the belts

HOPE THIS HELP ONE BELT ROUTING
Regards Paul
www.limotec.co.uk

I believe you have 2 beltson this engine. One for the alternator, a short skinny one. Loosening the alternator bolts and pulling the alternator towards the front of the car, and then tightening the adjusting bolt.
The other belt runs the power steering, a/c compressor and water pump. I think it has an idler pulley with a jack screw adjusting screw. loosen the screw to releive belt tension. good luck