How do i remove the front bumper on a 2013 kia sorento

You have to get under the vehicle, remove the skid plate and reach up from to them there. It's kind of a pain but managable. I found that a drill with a 90° attachmemt makes it loads easier to remove fog light mounting screws if you need to replace the whole assembly. If your just replacing the bulbs all you need to do is twist the bulb housing and pop them out to access the bulbs. Good luck!

There appears to be a video on the Kia Forums

https://www.google.com/search?q=2003+Kia+Sorento+add+fog+lights&rlz=1C1QJDB_enCA643CA644&sxsrf=AOaemvLztsfiHqAoQ6JpkfoTsWX-4MhIdQ:1642474312717&source=lnms&tbm=vid&sa=X&ved=2ahUKEwjx5NjPpbr1AhUDXc0KHUYkC1MQ_AUoBHoECAEQBg&biw=1920&bih=937&dpr=1

..

I have recently replaced the front bumper on my 2005 Aveo, after hitting a deer. The good thing to know, is directly connected to the bumper, there is NO sensor to worry about tripping the airbags. There are what seems like a million Teflon screws, that must come out to remove, and replace the bumper. The turn signals, and fog lights(if equipped) must come out first. All electrical connections, like the headlights, turn signals, and fog lights, must be disconnected, or you can't access the bolts, and screws near them. It's actually very easy to remove and install the bumper after the electrical connections are dealt with. Do not worry about the plastic clips located under the hood for removal. They are cheap and easy to replace. Here are some pics that might help you.
Front bumper front and back.

Teflon screws.

You need the Hiscan tester or the PC type (newer) Kia dealer can do it.

Hi!
Do you mean the lights itself, or the lights on the dashboard confirming that they are on?

Hi,

I drive a kia sorento and i have had a similar problem. I have a hitch on the back and the electrical connection was bad and kept blowing fuses. I removed the electrical hookup. Easy to do as it is a plug conected to the harness of your vehicle. Located underneath your vehicle just above the rear wheel well on the passenger side. Your fuse panel is located under the hood of your vehicle next to your battery. Remove fuses one by one and check for any that are blown. I hope this helps.

Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1

Fig. 1: Exploded view of a fog lamp assembly

1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
2. Remove the reflector assembly from the lamp body.
3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.

1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
2. Turn the fog lamps ON and adjust as follows:
   1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
   2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
      
3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic


www.autozone.com

Notes FOG LAMP BULB REPLACEMENT - FRONT

REMOVAL PROCEDURE

1. Remove the front bumper fascia deflector.
2. Disconnect the electrical connector from the front fog lamp bulb/socket. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Rotate the front fog lamp bulb/socket counterclockwise to release.
2. Remove the fog lamp bulb/socket from the front fog lamp assembly.

1. Install the fog lamp bulb/socket to the fog lamp rotating clockwise until fully seated. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Connect the electrical connector to the front fog lamp bulb/socket.
2. Install the front bumper fascia deflector.

On the left switch stalk, there's a rotating ring that turns on the fog lights (only when the headlights are also on).