Need to know the location to test
SOURCE: Location of EGR Valve
Found the info!!
This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold.
To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet.
There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said.
With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out.
For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed.
Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection.
Please don't forget to rate!!!!
SOURCE: need to know where the egr valve is located on a
It is located on the intake manifold behind the throttle body
SOURCE: EGR Valve on mazda3i
It's not the EGR valve...Find an independent mechanic in your area that will "scope" the engine for around $50 or less. My guess is one or more of your O2 sensors are fouled. If you'd like to try a cheap fix...Buy a can of "SeaFoam" at Advance Auto Parts ($9) and add it to your gas per instructions...drive at least 100 miles.
Good Luck
SOURCE: i need to know where the egr valve is located
EGR stands for EXHAUST GAS RECIRCULATION.
This is a loop back system between your exhaust manifold and the underside of your filter.
The EGR valve is located between the inlet (exhaust manifold) and the outlet (intake manifold).
About 8-12" below the air filter....toward the passenger side.
EGR carbon built up can be clean.
Check the soft membrane on the EGR valve and see is it crack/torn. If it's in good shape then you may reuse it.
The professional use a vacuum hand tool to determine the travel of the EGR.
There are carbon built up inside the EGR air passage tube too,
Make sure you give both a good cleaning.
The EGR base gasket MUST BE REPLACE!
Order one before you start the job.
Please post more info on the comment window.
SOURCE: location of EGR valve for 4.6 liter engine
EGR VALVE IS #2.
Please wait for second post to answer your second question....comes with a few pictures.
Testimonial: "thanks c17hydro ...looks like the proper proceedure,,,will try fix tomorrow"
2,926 views
Usually answered in minutes!
I think everybody is having this problem. My husband is trying to replace ours and gave up looking. This was most helpful!!!!!
I need to find the location of my egr valve on a 4.7L dodge ram.
×