Where are the fuses for the 4x4 located on a 05 envoy

What code's ? # code's P0 what ? Any BCM - body control module code's ? Did you do diagnostic test's for said code's ? Do you know what a factroy diagnostic flow chart is ? Is the vehicle a 4X4 or 2X4 ? What engine ? Do you know what class 2 serial data bus is ? Do you have wiring diagrams ?
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch headlamp on signal circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.

High Beams
The high beam headlamps receive voltage from the headlamp HI relay located in the underhood fuse block. The body control module (BCM) controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block. The right and left headlamps are grounded at G100 and G104.
The high beam indicator is illuminated when the instrument cluster receives a class 2 serial data message from the BCM that the high beams are illuminated.
Low Beams
The low beam headlamps receive voltage from the headlamp LOW relay located in the underhood fuse block. The body control module (BCM) controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent and are fused independently in the underhood fuse block. The right and left headlamps are grounded at G100 and G104.

DTC B2645
The body control module (BCM) monitors the ambient light sensor signal circuit in order to determine if the daytime running lights (DRL) or the auto headlights (ALC) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor signal voltage is between 1.75-4.9 volts, either the DRL will be commanded ON or the ALC will be commanded ON depending upon the amount of light received by the sensor.

DTC B2645 Ambient Light Sensor Circuit

the front axle actuator is stuck engaged. the actuator is located on the right side of the front axle. the part is easily replaceable.

sound like problem in shift motor and shift switch.

On these issue, there are few solved help links for troubleshooting the issue easily.-------

Click the link below: ---

No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

-----------

4X4 Truck makes roaring noise in the front end?

http://schematicsdiagram.blogspot.com/2012/01/4x4-truck-makes-roaring-noise-in-front.html

-------------

Car will not go into 4WD high or 4WD low?

http://schematicsdiagram.blogspot.com/2011/12/car-will-not-go-into-4wd-high-or-4wd.html

--------------

No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

------------

4 wheel drive system will not disengage?

http://technoanswers.blogspot.com/2012/01/4-wheel-drive-system-will-not-disengage.html

----------

4WD light is flashing and beeping? NO 4WD high?

http://schematicsdiagram.blogspot.in/2012/02/4wd-light-is-flashing-and-beeping-no.html

----------

2002 Jeep Wrangler: 4WD Idiot Light is ON?

http://technoanswers.blogspot.in/2012/06/2002-jeep-wrangler-4wd-idiot-light-is.html

----------

Traction control switch will not engage on 4WD High or Low

http://whoisbyme.blogspot.com/2012/10/traction-control-switch-will-not-engage.html

-----------

4WD light flashing and 4WD will engage after few minutes

http://repairhelpcenter.blogspot.com/2012/10/4wd-light-flashing-and-4wd-will-engage.html

------------

2008 Toyota Tundra: 4x4 Wheel Drive Light is Flashing?

http://technoanswers.blogspot.in/2012/05/2008-toyota-tundra-4x4-wheel-drive.html

----------

4x4 front differential will not engage the axle on ford?

http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html

-------

4x4 will not engage on Ford F150?

http://technoanswers.blogspot.in/2012/02/4x4-will-not-engage-on-ford-f150.html

-------------

Dodge Ram 4x4 light keeps flashing

4X4 LOW LIGHT IS FLASHING ON DASH

http://technoanswers.blogspot.in/2012/09/dodge-ram-4x4-light-keeps-flashing.html

----------

Ford 4x4 front wheels will not engage?

http://technoanswers.blogspot.in/2012/02/ford-4x4-front-wheels-will-not-engage.html

-------------

These details will help.

Thanks.

check to see if the coolant fan comes on when u turn on the a/c...if it doesnt ur a/c system is over heating allowing the pressure in the system to build up to high...this will cause the system to shut down because the high pressure switch will shut off the system.. or if the system is low on charge it wont turn on until the engine heats up building up enough pressure in the systen for the low pressure switch to turn on the system..

Fix your car right away by clicking the link I attached
GMC Envoy 2002 to 2009 Service Workshop Repair manual

It has its own relay, replace it and check other relay and fuses affiliated with it. If ones out, it will cause this problem. Relays are in the hood compartment.

try resetting the shift module located inside behind passenger side kick panel,its white with a led light on top.

Check your headlamp relays under the hood, should be located on either the L/H or R/H fender well , could be inside a black plastic box labled fuses and relays... there will be a label on the underside of the lid to this box locate the relays as per lables... please rate my help thanks...

should have some kind of fault light on to read fault codes

its mostly an electronic solenoid shift system
could be a transfer box fault