Pcm code 1388 - 2000 Jaguar S-Type

Ford anti theft code 13 incorrect key . Most likely the chip in your key is wore out . After three incorrect trys it goes into lock mode witch takes up to 90 mins to clear

P1388 JEEP - ASD or CNG (compressed Gas) Relay Control Circuit Possible causes - Faulty ASD Relay (most common cause)
- Faulty CNG Relay
- ASD or CNG Relay harness is open or shorted
- ASD or CNG Relay circuit poor electrical connection
- ASD or CNG Relay poor ground or supply voltage condition

P1399 is a related to the P1388 failure.

Do you know what a ASD relay is ? Does the vehicle start ? http://www.dtcsearch.com/P1388/Chrysler

this indicates a problem with the variable camshaft timing and possibly requires reprogramming PCM module
assume the engine warning light is on? does the engine run normal?

P 1388--Variable Cam Timing Over- (Bank 2)


VCT solenoid valve stuck open
Camshaft advance mechanism binding
Need Correct Oil Filter

I will speculate here & say you don\'t run 5W-20 full
syn oil & don\'t change every 4,000 miles since motor
was new

Now you have oil flow issues with the solenoid or failed
cam actuators

I'm looking at the same thing. Associated with sporadic engine stoppage.

No voltage sensed at the PCM (powertrain control module) when the ASD (auto shut down) relay is energized. It could be the ASD relay, the PCM, possibly their relays.
If you are interested in further diagnosing the problem, I will be happy to assist you.

P1383= VVT over retarded bank 1.
P1388= VVT over retarded bank 2.

There is an issue with your variable valve timing system. It will need further diagnosis.

Auto shutdown relay control circuit=p1388

IPC stands for Instrument panel control, here is a typical code repair flow chart, this is for example only and has nothing to do with your car..
P083 = 24x signal high.

P107 = Instrument panel control )IPC) to computer (PCM) data problem.

P137 = Loss of Automatic braking system (ABS) to Traction control system (TCS).

What you need to do is CLEAR all these codes from the computer and see which ones return.

Perform this test.

1. Ignition key ON. Engine OFF.

2. Simultaneously push and hold the OFF and WARMER (^) buttons on your climate control panel for 3 seconds and release them.

3. Diagnostic codes such as above will appear with the word HISTORY or CURRENT for each code.

4. The codes will stop when you see PCM?

5. Push and release the HI(^) button and you will see PCM DATA?

6. Push and release the LO(v) button and you will see PCM DATA?

7. Continue to push and release the LO (v) button until you see PCM CLEAR CODES?

8. Push and release the HI(^) button until you see PCM CODES CLEAR.

9. Turn OFF the ignition and wait 3 minutes and try and start the car. If the car starts and the light comes back ON, Turn OFF the car and repeat steps 1 thru 3 and let me know what codes you get and if they are HISTORY or CURRENT.

10. When you see PCM?, Turn OFF ignition key.

11. Let me know what codes you get and if they are HISTORY or CURRENT.



---------- FOLLOW-UP ----------

QUESTION: this is what happen when it did what you told me what to do.
P047 History,P107 History,No IPC Code, P83 History,P137 History, A047 Current, No Sir Codes, T072 History,No Russ, PCM?
ANSWER: You did not follow the directives correctly . If you had, You would NOT have any HISTORY CODES.

Try it again and follow these directives EXACTLY:

1. Ignition key ON. Engine OFF.

2. Simultaneously push and hold the OFF and WARMER (^) buttons on your climate control panel for 3 seconds and release them.

3. Diagnostic codes such as above will appear with the word HISTORY or CURRENT for each code.

4. The codes will stop when you see PCM?

5. Push and release the HI(^) button and you will see PCM DATA?

6. Push and release the LO(v) button and you will see PCM DATA?

7. Continue to push and release the LO (v) button until you see PCM CLEAR CODES?

8. Push and release the HI(^) button until you see PCM CODES CLEAR. WAIT 3 seconds and then proceed to 9.

9. Turn OFF the ignition and wait 3 minutes and try and start the car. If the car starts and the light comes back ON, Turn OFF the car and repeat steps 1 thru 3 and let me know what codes you get and if they are HISTORY or CURRENT.

10. When you see PCM?, Turn OFF ignition key.