P1494 code check engine light is on.what needs to be replaced?

didnt specify so check these links for assistance p1494 code what exactly is and where is the part located P1494 EVAP Leak Detection Pump Switch or Mechanical Fault Trouble Code P1494

You can not work on a vehicle as your doing

Your checking for generic codes only & throwing
parts at it

You get a couple possible worn or failed parts & have
a few less codes

There is no need to clear ALL Data every time you change a part

You need to STOP

You need professional scan tool software to look at ALL data & go for a road test first

You keep clearing stored data ,so now the process will take longer

You work one code & one system at a time

NO PARTS get replaced that are not tested & found to fail
a test,thus a worn out part.

You need both Factory Emission & Diagnostic Manual, as well
as Wiring Diagram Book-- BEFORE-- you can even walk to the vehicle (Helm.Com)

You have nothing to go by,no system knowledge & no trouble charts,& no wiring diagrams to start your testing

If you got no scan tool & no volt meter & no oscilloscope,
your done,vehicles have to be tested to find a problem,any
problem,resolve it & continue on.

kia ora Mark , greetings , sorry bro these code things are beyond me ive been driving around with a p0161. i believe its a bank2 down stream sensor for 2 years , maybe you can help me , 2002 grand cherokee 4.7 Ho , do you know what brand of sensor or part numbers i need , an idea of cost for same . i forgot to mention i am in New Zealand and auto parts are so much more expensive here , no idea at all , much help needed everyone thank you all , hope you get sorted Mark cheers mate

P1494 code is a leak detection pump switch or mechanical fault, leak detection pump switch does not respond to input. The leak detection pump (if equipped) is located under the air filter housing on models through 2001. Check if the vapor and vacuum lines are securely connected to the leak detection pump or a diagonstic trouble code my be set like this. The leak detection pump switch may be bad and need replaced.

P1494 - LEAK DETECTION PUMP SWITCH OR MECHANICAL FAULT . There is a service bulletin for certain years pertaining to this problem . Some cars will fill the vacuum line going to the LDP with oil , causing this dtc to trip . In most cases you can clear this and it won't come back-also, check your gas cap, it needs to seal the system, if it is loose or leaks, it can set this code.

Check the answer in other post mine: Grand Cherokee Jeep code P1494

Hope helps (remember to rate this).

The Dodge P1494 engine light code means Leak Detection Pump Switch or Mechanical Fault. A proper diagnosis must be done, you can't simply replace the LDP and expect that to fix the problem. It shouldn't hurt anything to keep driving it for a while until you can get it fixed.
There is a technical service bulletin that applies to your vehicle and it mentions that code specifically. I'm including it here for your information: TSB-18-01-00
SUBJECT: Misdiagnosed Leak Detection Pump Systems With DTC P1494, P0442, P0455, OR P0456.
MODELS: 1997 - 2000 (LH) Concorde/Intrepid/LHS/300M/Vision and others
DISCUSSION:
During evaporative system diagnosis, Leak Detection Pumps have mistakenly been replaced. A thorough inspection for pinched, kinked, or disconnected supply vacuum lines (as currently listed in the Powertrain Diagnostic Procedures) is a critical step in diagnosing DTC P1494 (LDP SW OR MECHANICAL FAULT). Additionally, the other evaporative leak faults (DTC P0442 - SMALL LEAK, P0455 - LARGE LEAK, and P0456 - VERY SMALL LEAK) should have the supply vacuum lines examined for pinches or kinks prior to any LDP component replacement. The supply vacuum lines should be checked from the engine compartment all the way to the fuel tank, including the LDP and purge system.

NOTE: VERIFY ALL RELATED SUPPLY VACUUM LINE ROUTINGS FOR PINCHES, KINKS, OR DISCONNECTION'S BEFORE REPLACING LDP SYSTEM COMPONENTS.

Hope helps (remember rated and comment this).

danbalue, a code P1765 means Transmission 12V Supply Relay Control Conditions and P1494 means EVAP LDP Pressure Switch Fault Conditions.

I found info on the following codes:
P0443 - http://www.obd-codes.com/p0443
P1494 - http://www.check-engine-light.com/dodge

Good luck.

P1494 Leak detection pump pressure or mechanical fault, hope this helps

These are all related sensors and active devices of the evap system, clear the code and replace the fuel cap.