Question about 2006 Chevrolet Uplander

1 Answer

Turn signal wiring diagram for a 2006 uplander

Replaced all the bulbs and the turn signal still isnt working right.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 48 Answers

What are all of your symptoms?
1 bulb or all?
Front and back?
Help us help you.....
Dean

Posted on Sep 19, 2018

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 216 Answers

SOURCE: brake wiring diagram chevy lumina

why not just replace the turn signal switch must faster and safer . buy one from your local parts house then you can see its not that easy to install but you can do it with a little help

Posted on Aug 26, 2009

alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: 2004 Chevy Malibu turn signal issues

check the bulb with a test meter and alsof or a feed

Posted on Nov 25, 2009

Anonymous

  • 5 Answers

SOURCE: How do i replace the front turn signal bulb on my

To get at the turn signal bulb, you gain access to it by first removing the headlamp housing which is directly above it. Remove the top bolt and locking pin (as you mentioned), then remove the headlamp housing by pulling it (or pushing it from behind) straight forward to release the friction pressure clip located near the outside edge of the housing. To prevent damaging the headlamp housing's rubber gasket, you may have to first release several of the plastic grille's black plastic clips nearest that housing by pulling upward on the clip heads and removing them; they are re-useable. It's simple and quick to do once you've figured it out. I carry spare bulbs...beats getting a ticket.

Posted on Feb 20, 2010

Anonymous

  • 1 Answer

SOURCE: I want to replace the left rear turn signal bulb

Open your lift gate and you will notice the lamps are incased in a black plastic housing. There are 3 star screws you need to remove in order to pull out the housing and change the bulb. You may need to buy a a special screwdriver or bit for one.

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

1 Answer

1995 Chevy Caprice Wagon, right side signals and brake lights dont work


change the bulb if still out then check and test socket/ground wiring/wire harness for damage

Apr 28, 2017 | Cars & Trucks

1 Answer

Turn signal bulb was working, now it isnt


its is not uncommon for the contacts in the sockets to become corroded or just expand to the point of where they do not contact the bulb,try to test the socket with a multimeter for voltage,if it has voltage then its most likely the contacts,which sometimes can be rebent,but replaceing the sockets is a better solution,and can be picked up at most stores or 4x4 shops and junk yards.

Dec 14, 2011 | 1998 Jeep Cherokee

1 Answer

Turn signal not working


i had this same problem and i alleviated it by replacing the column switch which isnt an easy task and I used a manual (which can be obtained at the library for free or you can buy one at your loccal book or auto parts shop)

Aug 26, 2009 | 1994 Buick LeSabre

1 Answer

Right Turn Signal sitll not working eventhough I replaced the flasher


are you sure the bulb is good? have you had the steering column out recently? if so make sure the plug going into your switch isnt being pulled as it will cause a bad connection. but it sounds like you need a new turn signal switch

May 05, 2009 | 1998 Ford Contour

Not finding what you are looking for?
2006 Chevrolet Uplander Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...