P0753 After starting put in drive it is in high gear you can turn it off and restart and it will be in low gear but will only shift once will not shift into drive some times if i get lucky i can turn it off and restart it will shift into drive .But the last few times it will not shift into drive.I have a code P0753.

did you turn the locks on the wheels, or check the fuses

Your best bet would be to take your vehicle to a ASE certified professional . You do not have the tools to diagnose this or the information.
DTC P0753
The 1-2 shift solenoid (1-2 SS) valve controls transmission fluid pressure acting on the 1-2 shift valves to position the valves for the appropriate gear. The 1-2 SS valve is a normally-open exhaust valve located on the control valve body. A fused circuit supplies ignition voltage to the 1-2 SS valve. The PCM commands the solenoid ON or OFF by switching the ground path. When the 1-2 SS valve is commanded ON, the PCM senses low voltage. When the 1-2 SS valve is commanded OFF, the PCM senses high voltage. Refer to Shift Solenoid Valve State and Gear Ratio .
If the PCM detects a continuous open, short to ground or short to power in the 1-2 SS valve circuit, then DTC P0753 sets. DTC P0753 is a type B DTC.
DTC P0753 sets when one of the following conditions occurs for 5 seconds:
Condition 1 The PCM commands the solenoid ON and voltage feedback remains high, B+.
Condition 2 The PCM commands the solenoid OFF, and the voltage feedback remains low, 0 volts.
DTC P0758
The 2-3 shift solenoid (2-3 SS) valve controls transmission fluid pressure acting on the 1-2 and 2-3 shift valves to position the valves for the appropriate gear. The 2-3 SS valve is a normally-open exhaust valve located on the control valve body. A fused circuit supplies ignition voltage to the 2-3 SS valve. The PCM commands the solenoid ON or OFF by switching the ground path. When the 2-3 SS valve is commanded ON, the PCM senses low voltage. When the 2-3 SS valve is commanded OFF, the PCM senses high voltage. Refer to Shift Solenoid Valve State and Gear Ratio .
If the PCM detects a continuous open, short to ground or short to power in the 2-3 SS valve circuit, then DTC P0758 sets. DTC P0758 is a type A DTC.
Conditions for Setting the DTC
DTC P0758 sets when one of the following conditions occurs for 5 seconds:
Condition 1 The PCM commands the solenoid ON and the voltage feedback remains high, B+.
Condition 2 The PCM commands the solenoid OFF and the voltage feedback remains low, 0 volts.
What's this p91860 , no such code .

P0753 - Shift Solenoid A Electrical
- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 'A' valve
- Shift solenoid 'A' valve harness or connectors
- Shift solenoid 'A' valve circuit is open or shorted


Read more: http://engine-codes.com/p0753.html#ixzz31EB1WygL

Tourqeconverter lock switch or sensor////

P0753 Shift Solenoid A Electrical its inside of transmission not very easy to replace it controls the shifting of the transmission
P0763 Shift Solenoid C Electrical its another transmission shift solenoid
P0758 Shift Solenoid B Electrical another shift solenoid now my question to you is your transmission shifting normal have you had any work done to your car recently like changeing any seals on your transmission to have theses replaced by a mechanic its gonna be very expensive i could tell you step by step how to change them with theses codes you should be haveing serious shifting issues if you dont have shifting issues reset codes and see if they come back if they do then it could be in the wireing harness comeing from transmission hope this answers your question happy holidays

i have this same problem with my jeep. i am going to change the shift solenoid out.

not sure if this is the answer yet but i have the same problem with the same codes i work at an auto parts store and a few of the techs that are customers have lead me in the direction of changing the ignition switch, i am doing it today will let you know if it solves the problem

Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

I agree, this is a lot of codes. I would tend to think this would be electrical, perhaps computer are a loose connection? These trannys I have rebuilt so far usually have a couple of codes related to the problem but not this many - all over the place.

I have a 94 lexus es 300 and I have the same problem the check engine and o/d light is on and it drives slow in first or second and then it will shift into 3rd with no problem i went to a tranny shop and they replaced the p0753 Shift Solenoid A Electrical and the p0773 Shift Solenoid E Electrical and drove around the block and after 15 mins the lights came back on and car acted the same way and got the same codes so he didnt charge me anything and was like he didnt know what it was so now im stuck with a car that doesnt have 1st or 2nd gear so if anyone can help im open for anything