How do you change the headlight

Most of the headlights do not unbolt to change bulbs. If it's a blown bulb you're trying to replace, look on the back side of the headlight housing. There should be a plug with wires attached going into the back. This plug should twist either to the right,left or up or down. Once you've twisted this plug out of the headlight housing you'll see the bulb you need to replace. Unplug the wire harness from the blown bulb and place it into the new bulb, being careful not to touch the new bulb with your bare hands as any oil or other contamination will cause these bulbs to blow as soon as they are turned on. Place the new bulb with harness back into the socket in headlight housing and twist into position.

Re: Replace headlight bulb

1. INSTALLATION GUIDE:
2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
3. Parts Identification:
4. Projector Headlight
5. Halo & L.E.D.
6. Bottom of the Headlight:
7. Ballast Bracket, Halo Wires(red/black)
8. Turn Signal Adaptor
9. TOOLS REQUIRE
10. 10mm - 8mm socket
11. Philip Screwdriver
12. Crimper/Pliers
13. For more information about how to install your vehicle, come visit our youtube page on
14. http://www.youtube.com/spyderauto
15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
21. STEP:
22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
24. Factory Xenon Headlight
25. Spyder Projector Headlight using Factory Xenon Lights
26. STEP:

BMW e46 HID Headlight Replace

did you blow a fuse when changing the light over?

you need to remove the front wing on the side that the bulb has blown,and the centre panel, then there are 3 torx bolts holding the light assy in.then its just the bulb unit clips out.

how do you change front headlight blub 2008 sonata

open the hood
remove the push pins on the front panel across the rad remove panel
there will be 2 retainers they will be black or white can't remember
lift up on the retainers
pull the headlight forward
change the bulb then reassemble
hope this helps

Here is a link to help you locate the parts you need: http://www.usedpartslive.com/live/1/year/HONDA/model/Front_End_Bra/

You may also try a google search under JDM (Japanese Domestic Market) Parts
Good Luck Raz,...

Best method that I found is to just take the 6 phillips screws (4 in the well and 2 below the front bumper cover) out of the forward wheel well panel and reach in behind the panel to the headlight assembly.

you should be able to access the connector and bulb without removing headlight assembly. lift the hood and you should see the connector behind the headlight.

Depending on whether it is the front or the back turn indicator light will determine on what needs to be done. If it is the front turn indicator light open the hood of the car you may need to take the entire headlight out. The headlight may have screws, take the screws out then the front light will come out from the outside of the vehicle replace the burned out bulb. The bulb should snap right in and then put the headlight back in make sure you put all screws back in from the inside of the hood. Step2 If it is the back turn indicator light, go through the trunk of the vehicle. If there is a panel covering the lights you must unscrew the panel and then replace the burned out light bulb. Some panels can be folded down without removing all of the screws to access the lights. This light may not require for you to pop the entire light out you maybe able to just replace the bulb. After you have replaced it screw the panel back into place. The back light should not require the entire light to be lifted out just a simple bulb replacement. Step3 In replacing either the front or the back indicator light you must gain access to the turn signal housing which is usually in the same case as the headlight or your rear lights. It is very helpful to also get the owners manual out this will tell you exactly what type of bulbs you will need to get to replace the indicator bulb.