- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If you are removing the harmonic balancer for repairs, you will need to remove the engine and use a harmonic balancer bolt puller.
Do not try to remove this and run the engine. This will cause crankshaft failure due to the engine vibrations caused by the firing cylinders.
Yes. Jack the car up securely. you need to take passenger wheel off.remove caliper off . remove rotor. remove shock assembly and wheel bearing assembly slide.axleshaft out of the way.take serpinetine belt off. remove cover so you can see and access harmonic balancer.use impact to take bolt out of harmonic balancer.use wheel puller to take off harmonic balancer. Crank sensor should be right under harmonic balancer.
CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.
YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.
In order to remove your harmonic balancer, you will need a harmonic balancer puller. Most harmonic balancer pullers work and look the same. For your specific car it doesn't need a specific one. You can go and pick one up at your local auto parts store. You can either buy it or rent it, depending where you go. Hope this helps.
usually all crankshaft sensors are located right next to the main drive pulley (Harmonic balancer). As far as being easy is concerned some are not so easy as some require the removal of the harmonic balancer to get to it.. but you might be lucky Gm is pretty good at making the Crankshaft sensor accessible without removing the harmonic balancer.
First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.
×