2005 toyota solara rear rotor brake assembly

Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

are you saying that the brake calliper body has the special bolts holding it to the axle housing that you cannot undo and you cannot move the callipers back off the discs to get the discs off
to get the correct tool to do the job , ask a brake specialist shop for the tool size

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

The piston brake pad assembly is usually held in place by two bolts that face the car. Remove these and tap the assembly off .Hang the assembly from a wire.remove the two larger bolts that hold the rest of the assembly in place and remove the rotor.I would simply replace the rotors with after market rather than bother with the old ones.Replace rotor and larger cage.taking carefull note remove the brake pads and compress the brake piston with a C clamp. They should push back with minimal resistance.Check all brake components at this time including the large pins the brake assembly move back and forth on. Install your new pads and replace all the bits.Good luck.P.S. A digital camera might be helpfull if you haven't done this kind of thing before

Installing new brake pads on toyota camry solara 2006 front rotors and pads and rear pads. Steering wheel would shake while breaking on 50+ miles per hour speeds. All fixed now.

If you are saying the brakes chatter or there is a vibration when applying the brakes your rotors are warped. Remove the pads, have the rotors turned at a machine shop, and replace the pads with new ones, even if they look good. Warped rotors are caused by excessive braking at high speed, riding the brake pedal, or not correctly torquing the lug nuts to the correct lb/ft when installing the tire/wheel. Your owner's manual will list the correct torque which will be around 80 lb/ft. Make sure anyone removing a wheel use a torque wrench and torque them correctly.

Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Here is Video of How to replace front brake pads and rotors, and rear brake pads on toyota camry solara 2006

You need to go into the access hole in the rotor and back off the park brake shoes, which are located inside the rotor.

So this is what it takes to replace rear brake rotors on a 2003 Mercedes E320;
1) open the bonnet (hood) of the car and loosen/remove the cap off of the brake fluid resevior.
2) remove outer spring clamp from brake assembly (it clips in to the iner edge of the holes of the caliper).
3)using a 7 MM allen wrench, remove the brake caliper.
4) using 18 MM box wrench, remove the caliper housing assembly off of the wheel hub.
5) using a star wrench, unscrew the rotor locking screw from the rotor
6) squirt some liquid wrench on the rotor hub and knock the rotor with a hammer to work the liquid wrench in.
7) using the same hammer, knock the rotor off the hub.
8) using a metal file, lightly file old residue off of the hub and place the new rotor on the hub.
9) set the hub by screwing in the lug nuts and then screw in the hub locking screw using the star wrench, then remove the lug nuts.
10) reinstall the caliper housing assembly onto the wheel hub using the 18 MM box wrench.
11) push back the brake claiper piston to its home position and install the inner brake pad (the one with the snap clips)
12) insert the outer brake pad in the claper housing assembly.
13) slide on the caliper housing with the inner brake pad in place (over the outer brake pad) and screw in the caliper screw rods using the 7 MM allen wrench
14) on the right wheel brakes, DO NOT FORGET to slide in the brake sensor (the one with the black connector) and connect it to the connector on the caliper housing.
15) be sure to reinsert the spring clamp onto the outer brake assembly to set the assembly squarely onto the wheel (there should be no wiggle in the brake assembly after the spring clamps are installed).
16) finally mount the wheels.
17) you can bleed the brakes at this point to release any trapped air (which is unlikely) but be sure to pump the brakes after starting the car BUT BEFORE MOVING IT to re-preassurize the brake system before driving the car.
17) ONE WEEK LATER - recheck brake assembly to ensure all is okay and brake fluid.

This proposed solution is for a 2003 Mercedes Benz E320 and NOT a 2005 model as stated by the limited option selection provided by FIXYA.com when initially describing the problem.