Will a 1999 suburban air pump work on my 2000 suburban

Diagnostic Test Code (DTC) P0410 indicates that your secondary air injection system is not functioning properly.
Not all 2001 Chevrolet Bazers are equipped with secondary air injection. The secondary air injection system was added to vehicles that were to be sold in certain areas where the emissions laws required it, like the State Of California.

The Powertrain Control Module (PCM) monitors the system by commanding the secondary air blower motor to run and the air injection solenoid to open. This causes additional oxygen to enter the exhaust system. The PCM then monitors the signal from the oxygen sensors to see if the commanded air has in fact, entered the exhaust system. Code P0410 sets when the PCM has commanded the blower motor on and the solenoid open and there is little or no change in the oxygen sensor signal.

GM has had some problems with these systems and there has been a Technical Service Bulletin (TSB) issued that addresses some of the known concers. Below is a brief description of the TSB and the issues involved.

Bulletin No.: 04-06-04-015A
Date: November 28, 2006
TECHNICAL
Subject:
LN2, L43 or L35 Engine SES/MIL Light Illuminated, AIR Pump Ingesting Water and DTC P0410 Set (Replace AIR Pump and Inlet Hose Assembly)
Models:
1999-2003 Chevrolet Blazer, S10
1999-2001 GMC Jimmy
1999-2003 GMC Sonoma
1999-2001 Oldsmobile Bravada
with Vortec 2.2L I4 or 4.3L V6 Engine (VINs 4, 5, W - RPOs LN2, L43, L35)
Condition
Some customers may comment on the SES/MIL light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.
Cause
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.
Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly...

The bulletin goes on and gives detailed information on how to perform the repair and the part numbers of the replacement parts needed to do so. Your local dealer can provide the parts for you and you can probably get them to print out a complete copy of the bulletin for you. It is not really hard to do if you want to do this yourself.

code po411 secondary air injection system incorrect flow,possible causes , faulty air pump or faulty air pump vacuum valve or faulty check valve.

Hello, the air pump is located under the rad. on the lower core support towards the right. and yes you will need to replace the air pump, you will also need to install a updated hose assembly with a new filter. also in allot of cases the air pump fuse will blow when the air pump goes bad. the fuse is located by the battery in the right fender.

17803252
Pump Kit, Secondary Air Injection
1999-2000 L35

I think your car must be V6 or V8 engine, engine model 112, or 113, in your car secondary air injection pump is located on top of front, first remove front section of top engine cover then you can see black color electric pump have fitted middle of front end of engine that's the secondary air injection pump check any hose connection leaking or off or broken if not possibly faulty air injection pump, if you get fix the Mercedes diagnose tool to the your car it can activate and check by diagnose CPU, that's the easy way to find if it's faulty or not some time cold be faulty wiring or fuse. is this information helped you?

17828/P1420/005152 - Secondary Air Injection Solenoid Valve (N112): Electr. Malfunction Possible Causes

• Secondary Air Injection Solenoid Valve (N112) faulty
• Secondary Air Pump Relay (J299) faulty

Possible Solutions

• Check Secondary Air Injection Solenoid Valve (N112)
• Check Secondary Air Pump Relay (J299)

The secondary air injection pump relay (J299) is inside the engine compartment, left side, behind air cleaner housing, under a black plastic protective cover you can lift up to reveal it. It's near the brake fluid reservoir beside the odd black plastic cover for the wiring harness beside the shock absorber tower.

Rating my suggestion let's me know how helpful it was correcting your problem. Your rating is truly appreciated and would take the very least of time and effort away from you. Thank you

That's s failure of the secondary air pump. It'll have to be changed. It's an emissions component meant to help with cold start emissions. It won't cause engine running trouble but at inspection time you'll fail for smog. Change it before then and you'll be fine.

16795/P0411/001041


if (window.showTocToggle) { var tocShowText = "show"; var tocHideText = "hide"; showTocToggle(); } 16795/P0411/001041 - Secondary Air Injection System: Incorrect Flow Detected Possible Symptoms

• Malfunction Indicator Light (MIL) ON

Possible Causes

• Fuel Pump Relay (J17) faulty
• Hoses/Pipes to/between Components faulty/clogged
• Secondary Air Injection Pump (V101) faulty
• Secondary Air Injection Pump Relay (J299) faulty
• Secondary Air Injection Solenoid Valve (N112) faulty

Possible Solutions

• Check Fuel Pump Relay (J17)
• Check Hoses/Pipes to/between Components
  • Check Secondary Air Injection Hoses/Pipes for Carbonization
• Check Secondary Air Injection Pump (V101)
• Check Secondary Air Injection Pump Relay (J299)
• Check Secondary Air Injection Solenoid Valve (N112)

P1411 - secondary air injection system flow too low Bank 2.
P1423 - secondary air injection system flow too low Bank 1.
Check vacuum hoses to combi valves ,
most common split air injection pump which is riveted with aluminum rivets,ck rivets if they coming out ,pump doesn't build enough pressure.
In this case take pump out and put bolts instead of rivets all around pump case.Repl. all rivets not only broken one.Bolts sold at HomeDepot , just find a needed size.

Code is - Secondary air injection system, bank 2 flow too low.

Check fuse for sec. air injection pump.
Check vacuum hoses
Check piping from pump to sec. air injection valve. (combi. valve)

please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo