How to fix this dtc codes for car .thank u
The following link will provide you with all OBD-II codes for your Focus. CLICK HERE
This'll be your instrument cluster. I had the same issues random Engine Malfunctions when driving, no starting then after a while it would start it appear ok. I watched this video: https://youtu.be/myCVQhdtJ_s?si=d595cZ-5LvWdtWl7
and then took out my dash. MARK THE POSITION OF THE NEEDLES BEFORE REMOVING THEM!! Under the ***** eye, I couldn't see anything, not even using the mobile camera and zooming in. My son had a USB microscope and there it was, exactly as people were describing, cracked solder joint. The problem is that modern solder is not allowed to have lead in and as a result it is very brittle and power pins also produce heat so years of heating and cooling cracks the solder joints. If in doubt, just resolder all 32 of the Instrument Cluster connector pins. Hopefully that will solve your issue too. It took about 20 minutes to do, so not long, just watch the video and do exactly as it demonstrates, easier than you think.Personally, for the time it's worth resoldering all the pins on the Instrument Cluster connector on all older Focus' and Cmaxs and Mondeos as this is likely to happen in the future.
SOURCE: 2008 Ford F250 6.4 turbo diesel, have 3 DTC codes
P0087- low pressure fuel system. Fuel pressur valve stock open, Fuel volume control valve stuck close, Leaking fuel injector,P0088- fuel pressure contorl valve stuck close, Fuel rail pressure sensor P2291-all @ at the above, means to say poor fuel quality
SOURCE: ford mustang gt 2005 dtc codes
B1318 are related to low battery voltage .
B1202 is fuel sender circuit open.
P0463 is fuel level sensor circuit, (high input.)
If your gauge appears to be working o.k. all I would do for now is double check my voltage at battery with engine off & running, to make sure all is good there, erase codes & start fresh. The cheap way to erase is to remove neg (-) cable form battery for about 5 min., or more & then reconnect. You eill lose your memory on radio stations & have to re-set them though, otherwise have someone hook-up scan tool to erase them. Is vehicle starting & running o.k. at this time?
SOURCE: Battery recently died. Now
make sure your batt cables are tite--may need new one or cud hav charging problems--for codes you need to go Chiltons online or ask a dealer tech--however dont go replacin parts till you know for sure cause its $$ and discouraging Consult others 1st
SOURCE: Hi i have a ford focus 1.6 lx 06 on a 55 plate .
I was unaware of what these codes mean because on 1996 and later vehicles, cars are equipped with an OBD-II system which requires a scan tool that costs less than $100, these days.
The codes I see start with P or U, not D or E. And there are hundreds of them. If you scanned the codes using an obd-II scanner, and not the dash, I could tell you about that.
---
However, I looked at the Internet, and it said on the following forum that D900 meant a constant lean or rich condition:
http://forums.focaljet.com/duratec-tuning/478154-dtc-code-d900.html
The DTC E200 came up with the following link where it says invalid odometer data:
http://www.talkford.com/topic/127543-self-diagnostic-test/
After reading over your problem, it became apparent that this may not be a U.S. model due to the engine size not being 2.0L. Is this a U.S. or another country's model, since I didn't see that engine size listed?
13,549 views
Usually answered in minutes!
Can you retest this and report what the standard OBS2 codes are, they start with a "P" followed by 4 numbers.
DTC self diagnostic check resulted in above mentioned code.can anyone know about this.
DTC code not showing any code starting from 'p'
also showing ACCELERATION REDUCED,ENGINE SYSTEM FAULT
this ford European model duratec engine 1.6, i didn't get any code starting from 'p'. and same codes appear again.when i start car some times all gauges go down.battery,oil,handbrake,abs warming lamp come up.also i get acceleration reduced,engine system fault ' message.and car will go into limp mode.your suggestion please
I do not have the definitions, see your local MB dealer service facility.
E197 code need help to fix whatever is make that code pop up
×