Honda Civic Coupe Logo

Related Topics:

A
Anonymous Posted on Jan 30, 2018
Answered

My Honda Civic EX 2002 remote transmitter went out - I reprogrammed it but the drivers door will not lock/unlock with the remove. The drivers door also does not work with the switch to unlock/lock the door that is on the door - you have to manual unlock the lock or use the key from the outside.

Answer This Question

1 Answer

Jeffrey Turcotte

Jeffrey Turcotte

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Honda Master 8,991 Answers
  • Posted on Jan 30, 2018
Jeffrey Turcotte
Honda Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Aug 22, 2010
Answers
8991
Questions
7
Helped
4368800
Points
33683

Most likely the latch itself has failed. Open the door panel and first check to see if unlock signal is getting to latch connector. If yes, replace latch. If no signal, the problem is more likely in the control module.

5 Related Answers

Anonymous

  • 421 Answers
  • Posted on Aug 31, 2008

SOURCE: Car Alarm

sounds like the drivers side key switch has failed remove the interior door panel and there will be a switch attached to the back of the key lock cylinder or around there it should be two or three wires also check the door jamb wire harness where the door closes for any broken or damaged wires, use a vot meter and see if you get power or ground to the opposite side of the switch when you use the key to lock and unlock the door if nothing changes and there is power or ground! at this switch i would replace it, i don't think there is one but if the car has a passenger side key hole try to unlock the car from that side and see if you get the same problem -jeff

Ad

Anonymous

  • 15 Answers
  • Posted on Oct 20, 2008

SOURCE: 2001 Honda Civic door lock

If there is nothing jammed in the barrel, you will need to pull apart the lining of the interior of the door, disconnect the power motor for that switch, then see if it locks by key, sounds like the motor is seized, of out of allignment, easily fixed with a second hand or reco motor, or witha simple adjustment. Good luck, hope it helps.

Anonymous

  • 192 Answers
  • Posted on Apr 05, 2009

SOURCE: Honda Civic 2002 keyless entry

inspect and or replace the drivers door lock actuator...

Anonymous

  • 1 Answer
  • Posted on Jun 25, 2009

SOURCE: My 2door 2001 Honda Civic EX remote entry device

I used to install power locks on cars. Lets see if I can help...

Take off your door panel, find the small rod that is connected to the door lock itself (the part that actually shows if the door is locked or not) There should be an actuator of some sort connected to the small rod that pushes back and forth when you hit the lock button. This may have popped off or is loose/bent...

Or, There may be module inside the door that controls your locks either way, pop off your door panel and see what you got!

Anonymous

  • 1 Answer
  • Posted on Dec 08, 2009

SOURCE: Honda Civic: a locking/unlocking issue

Hi i have the same probelm, but if i open the drivers door within a second of pressing the remote all the doors open.

did u find a solution?

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I went through programing as far as lock recycling but wont go any further
Remote Transmitter Programming NOTE: All keyless entry remote transmitters must be programmed at the same time.
NOTE: Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.
  1. Turn the ignition switch from OFF to RUN eight times within 10 seconds, ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.
Read full answer
Mar 18, 2016 • 2004 Ford F150
0helpful
1answer

1998 Honda Civic Ex Coupe door locks
may need to be reprogramed download your workshop manual and follow instructions
Read full answer
Feb 06, 2014 • Cars & Trucks
0helpful
1answer

I have a 2000 ford mustang. Suddenly my keyless entry remote stopped working. I replaced the battery and turned the off and on 8 times and the locks cycled. after which i pushed the unlock but nothing...
The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:
  • generic electronic module (GEM)(14B204)
  • keyless entry remote transmitter (15K601)
  • NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
    Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
    Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
    • The doors do not lock/unlock using the remote transmitter
    • Ignition switch.
    • GEM.
    • Remote transmitter.
    • Remote transmitter batteries.
    • GO to Pinpoint Test C .
    You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
    1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
    1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
      Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
    1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
    1. Take an have the vehicle checked for DTC'S
B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM
Read full answer
Apr 12, 2017 • Ford Mustang Cars & Trucks
0helpful
1answer

Replaced batery in key fob and now there is no connection between fob and security system...I can lock and unlock doors with the key and I can start car ...fob doesn't work; does not lock or unlock...
reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.
Read full answer
May 18, 2011 • 1999 Toyota Camry Solara
0helpful
2answers

I used csorb's instructions to reprogram a master key for my 2000 Lexus RX300. The ignition works perfectly, but the doors don't lock or unlock.
Hi!!
I believe your alarm is in the PASSIVE MODE, here is how it works.

PASSIVE MODE Setting (Arming) Anti-Theft System The system will automatically set 30 seconds after following methods are performed: Remove ignition key from ignition switch. Exit vehicle, and close all doors. After performing this, anti-theft indicator on left side of instrument panel will light continuously for about 30 seconds. After 30 seconds, anti-theft indicator will blink once per second. When system is set, doors cannot be locked or unlocked using door lock control switch.
CANCELING THE ALARM AND REPROGRAMING MAY SOLVE YOUR PROBLEM.
Canceling Anti-Theft System Setting (No Alarm) When system is set (armed), but alarm is not sounding, use one of following methods to cancel system setting:
  • Unlock left or right front door using key.
  • Unlock all doors using remote keyless entry system.
  • Insert key in ignition switch and turn to ON position (this is operative only when anti-theft system has not been triggered).
HERE IS HOW TO REPROGRAM THE ALARM IN CASE YOU NEED TO RESET IT.
PROGRAMMING
PASSIVE MODE NOTE:Initial mode is passive mode off. If there is a different signal in middle of programming, signal is invalid.
Programming Passive Mode Off
  • Remove ignition key from ignition key cylinder. Ensure all doors (including back door) and engine hood are closed and unlocked. Perform all of following methods within 30 seconds:
  • Lock or unlock any door with key or remote keyless entry system.
  • Open driver door.
  • Lock and unlock driver door lock knob 3 times.
  • After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
  • Unlock driver door lock knob.
  • Close and open driver door 2 times.
  • Lock and unlock driver door lock knob.
  • After performing this, system should start force lock after 2 seconds. Passive mode should now be off.
Programming Passive Mode On
  • Remove ignition key from key cylinder. Ensure all doors, engine hood and luggage compartment door are closed and unlocked. Perform all of following methods within 30 seconds:
  • Lock or unlock any door with key or remote keyless entry system.
  • Open driver door.
  • Lock and unlock driver door lock knob 3 times.
  • After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
  • Unlock driver door lock knob.
  • Close and open driver door 4 times.
  • Lock and unlock driver door lock knob.
  • After performing this, system should start force lock after 2 seconds. Passive mode should now be on.
If you need further assistance, please provide an email address to send more info on your security system
Good Luck!! A 4 THUMBS UP rating would be greatly appreciated for this solution. Thank you for using FixYa!!
Read full answer
Mar 01, 2011 • Lexus RX 300 Cars & Trucks
0helpful
1answer

Wrwent to unlock my 1996 Hona accord with the remote and noticed the light was on. It wouldn't unlock the door . Put in a new battery and that didn't work. Do I need to reset the alarm? If so, how do I do...
Remote Transmitter Replacement (Wagon)
Use the following procedure when replacing one or both remote transmitters:
  1. Open the driver's door.
  2. Press and hold the driver's master door lock switch down in the UNLOCK position.
  3. Quickly insert and remove the key from the ignition switch five times, then insert the key the sixth time, and leave it in the ignition switch. (This routine must be done within 1O seconds.) All the doors will lock and unlock to indicate that the control unit is in the program mode.
  4. Press either button on the replacement transmitter. All the doors except the driver's door will lock and unlock to indicate that the control unit has accepted the transmitter into its memory. If either transmitter button is pressed again, all the doors will lock and unlock.
  5. To program a second transmitter, press either button on that transmitter. The doors should lock and unlock as described in step 4.
  6. Release the driver's master door lock switch.
  7. To exit the program mode, close the driver's door or remove the key from the ignition switch.
Read full answer
Dec 18, 2010 • Honda Accord Cars & Trucks
1helpful
1answer

I have a 2003 honda accord ex 4 door auto 4 cylinder. my problem is that the bat. on the remote control went dead now after i replaced the bat. with a new one it does not work? the light on the remote...
ok bare with me read carefully you need to program the new transmitter to your car.
1 turn igntion switch on (ii)second position
2 within 1 to 4 secs press the transmitter lock or unlock button with amied at the keyless receiver in the power master switch
3 repeat steps 1 and 2 3 times
7 confirm you hear the sound of door lock actuators working then press press lock or unlock button again or code won't be stored
8 within 10secs if you have other transmitters press unlock of each one
each time the doors locks and unlocks with operate 9 turn off ignition then there you go try them out
Read full answer
Jul 13, 2010 • 2003 Honda Accord
2helpful
1answer

How do i reprogram electronic door locks
Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.
Read full answer
Jun 05, 2010 • 1997 Ford Windstar
0helpful
3answers

Driver side lock
the solenoid may be weak, or it can be lubed. you will need to remove the door panel and see how it works, and try to lube it, or see if there is any binding.
Read full answer
Oct 12, 2009 • 1999 Honda Civic
3helpful
1answer

Keyless remote wont work
try to reprogram the remotes using these instructions..........
i assume for 02 explorer not th 05 frestyle listed (although similar procedure)
Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Make sure that the anti-theft system is not armed or triggered and key code programming is not active.
  1. Open the door, then press the driver door lock control switch UNLOCK button.
  1. Turn the key from OFF to ON 8 times within 10 seconds, with the eighth turn ending in ON. If the program mode is sucessfully entered the doors will lock and unlock to confirm.
  1. Press any button on a remote transmitter, and the doors will lock and then unlock all doors to confirm that the remote transmitter is programmed. All remote transmitters must be programmed within 20 seconds of each other. Up to four remote transmitters can be programmed to the vehicles security module each time programming mode is entered.
  1. If the door locks do not respond for any remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Locks, Latches and Entry Systems — Late Build or Locks, Latches and Entry Systems — Early Build in this section.
  1. NOTE: Exiting is acknowledged by locking and unlocking the doors if at least one remote transmitter has been programmed.
    Exiting the programming mode is accomplished if one of the following has occurred:
    • The key transitions to OFF.
    • 20 seconds have passed since entering programming mode or since the last remote transmitter was programmed.
    • Four remote transmitters have been programmed.
Read full answer
Jun 02, 2009 • 2005 Ford Freestyle
Not finding what you are looking for?

View Most Popular

Civic Coupe

  • Cars & Trucks

Related Question

I went through programing as far as lock recycling but wont go any further

  • 2004 Ford F150

Related Topics

137 views

Ask a Question

Usually answered in minutes!

Popular Questions

Belt routing diagram for serpentine belt on 2007

2007 Honda Civic GX NGV Sedan

Unlock code for my 2006 Honda civic radio

2006 Honda Civic Hybrid

Check Engine Code P1600 and P1433 for Hybrid

2004 Honda Civic

What is a Wrench light

Honda Civic Cars & Trucks

What is code error 1 on my honda civic radio?

2008 Honda Civic 1.8

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. Civic Coupe Manual

Civic Coupe

Loading...