Where is the location of code p1495 leak detection pump solenoid circuit

Do yourself a favor an take it to a qualified repair shop.
P1495 Jeep EVAP Leak Detection Pump Solenoid Circuit Condition

008 Chrysler Leak Detection Pump

answer courtesy of engine codes .com Engine-Codes OBDII Code List P1495 Dodge
P1495 Dodge P1495 Dodge - EVAP Leak Detection Pump Solenoid Circuit Condition 3 ' Add Comment Possible causes
- Faulty Leak Detection Pump (LDP)
- Leak Detection Pump (LDP) harness is open or shorted
- Leak Detection Pump (LDP) poor electrical connection
What does this mean? When is the code detected?
Malfunction is detected when the Powertrain Control Module (PCM) detected the pump solenoid did not change status when activated,
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors
P1495 Dodge Description
The Evaporative emissions system is design to prevent the escape of fuel vapors from the fuel system. Leaks in the system, ca allow vapors to escape into the atmosphere. The leak detection system tests for EVAP system leaks and blockage.
During the self-diagnostics, the Powertrain Control Module (PCM) first checks the Leak Detection Pump (LDP) for electrical and mechanical faults. If the first checks pass, the PCM then uses the LDP to seal the vent valve and pump air into the system to pressurize it. If a leak is present, the PCM will continue pumping the LDP to replace the air that leaks out. The PCM determines the size of the leak based on how fast/long it must pump the LDP as it tries to maintain pressure in the system.

Read more: http://engine-codes.com/p1495_dodge.html#ixzz3iQ8P3JII P1495 Dodge EVAP Leak Detection Pump Solenoid Circuit Condition

P1495 indicates a Leak Detection Pump Solenoid Circuit error. The Leak Detection system is located under the hood on the driver's side inner fender. The solenoid is located under or behind the leak detection pump. This system works in conjunction with the EVAP system, and one of the most common error causes is a loose or non-airtight gas cap. Try tightening or replacing your gas cap and see if the code disappears after a normal driving cycle (about 50 miles). Good luck.

code P1495 leak detection pump solenoid circuit malfunction. the leak detection pump located underneath the vechicle right behind lower left corner of the engine compartment.

Check your connections on your leak detection pump and vacuum hose to the engine. You will need a scanner to do a wiggle test on the wiring harness this is a common problem.

The code is telling you that you have a problem with the pump.

DTC P1495 - LEAK DETECTION PUMP SOLENOID CIRCUIT
WHEN MONITORED Ignition on and battery voltage greater than 10.4 volts .
SET CONDITION The state of the solenoid circuit does not change.

POSSIBLE CAUSES: Fused ignition switch output circuit open
Leak detection pump defective LDP solenoid circuit wiring harness observable def LDP solenoid ckt wiring harness intermittent def LDP solenoid control circuit short to ground Leak detection pump solenoid control circuit open Powertrain control module defective

Hope helps.

P0300 - generic misfire.
P0301 - misfire at cylinder 1 = the spark was not generated at some time at cylinder 1
P1494 - Evap Leak Detection pump pressure switch condition = the ECM detected the leak detection pump switch did not change after the solenoid was energized
P1495 - leak detection pump solenoid circuit = the electrical circuit that commands the solenoid of the pump is interrupted
You need to check the wiring to the solenoid and the solenoid itself, located under the driver's side in the cast cradle under the steering gear. A good expertise of car electrics is required for that, you will need a good repair shop.

P1494 Leak detection pump pressure switch or mechanical fault
P1495 Leak detection pump solenoid circuit
you have a problem with the fume extraction circuit like a motor or something

code p1495 leak detection pump solenoid circuit malfunction.problem could be in the leak detection pump.it could be faulty.

P1698 Chrysler

ECM fault-No CCD message from TCM
- Failed ECM

Probable Cause[s]

1. Open CCD bus line
2. Failed TCM

P1495 Chrysler

EVAP leak detection pump solenoid circuit condition
- ECM detected the pump solenoid did not change status when activated

Probable Cause[s]

1. Pump solenoid defective
2. Open or shorted circuit condition
3. ECM Defective

P1495 Leak detection pump solenoid circuit fault (open or short). It is located under the engine cradle near the steering rack and pinion. Check it's wiring. It detects EVAP system leaks.