Question about 2008 Mercury Grand Marquis

1 Answer

Location of blender door motor - 2008 Mercury Grand Marquis

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,803 Answers

The blend-air door actuator on a 2008 Merury Grand Marquis is located on the top forward area of the HVAC housing under the instrument panel. Complete instrument panel removal is required to access it.

Posted on May 27, 2012

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Temperature blender actuator fuse


There is not a seperate fuse for the air temperature control blend door actuator motor.

Jun 13, 2016 | 2005 Ford F-150

2 Answers

Where is the actuator located?


The blender door actuator, the one that most commonly fails on Windstars, is located behind the radio. Remove the radio to gain access. Is white.

Jul 12, 2014 | 2001 Ford Windstar

1 Answer

Where is the location of the blender door on a 1999 pontiac grand prix se


it is inside the heater/ac box which goes from one side to the other under your dash and is a monster to get out. check to make sure your actuator motor (which operates the blend doors) is working first.

May 18, 2014 | 2005 Dodge Dakota

1 Answer

2006 dodge durango climate control vent and blender not working


Yes, your blender door motor is failing. It is located under the dash.

Apr 05, 2014 | 2006 Dodge Durango

1 Answer

2008 mercury marquis blender door location


The blend-air door actuator on a 2008 Merury Grand Marquis is located on the top forward area of the HVAC housing under the instrument panel. Complete instrument panel removal is required to access it.

May 26, 2012 | 2008 Mercury Grand Marquis

1 Answer

Have no a/c or heater just blows ambient air


Probably a vacuum motor on the blender door has gone bad or the vacuum line broken or fell off.Find the blender door motor and with engine running,wheels blocked and emergency brake on in park,check the motor's operation. don-ohio

Oct 01, 2011 | 1996 Ford Explorer

2 Answers

Heater hot/cold control knob doesn't work need to have the hot air.


Check the motor on the top of the heater plenum. It turns a shaft to shift the blender door which controls the input to this plenum either the heater core or the evaporator core (ac). You may find the motor is OK but the shaft (plastic) has broken and the blender door has to be replaced. This is a costly job that involves removing this plenum after removing the dash. A shortcut I found online was to cut a hole under the blender door and replace it through this opening. After replacing you can seal up the hole with epoxy. I cut three sides of a square hole leaving the back uncut. Pull down and the blender door can be removed. My problem was on a 1997 Explorer. _6.gif

Nov 22, 2010 | 1998 Ford Explorer

1 Answer

Is there a rear blender door or motor for a 99 windstar how can I locate it.


Should find it in the right rear behind the rear trim panel.

Oct 23, 2009 | 2001 Ford Windstar

2 Answers

Had no heat-Mechanic replaced "bender" motor/epoxied sleeve. Now no a/c. Said he would have to change manually


Hi, I have a 2001 Windstar which had the same problem.The fix is to replace the blender door motor ($45.00) it's a little white plastic box located behind the radio under the dash board.  The plastic gears in the motor box can get broken (made in China). I had to remove about 8 screws, the radio, and then it was easy to replace. Before you purchase a new blender motor first check to be sure this is the problem. (1) The door on the glove box can be lowered and you can put your hand on the plastic box (the motor is insidethis little box) when you do this you can feel it clicking when you hear the clicking noise. (2) A service manual will tell you to disconect the battery but it's not nessary. (3) You may need to purchase a special tool to remove the radio. Mine has 4 little holes that uses two  special u-shaped tools you stick it in the holes, push them to the outside and pull the radio out.
I hope this helps. Warren

Oct 17, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

830 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...