1993 Chevy 1500 pickup 4-wheel drive

Chevrolet Suburban Questions - 4 wheel drive does not ...

www.cargurus.com > Questions > Chevrolet > Suburban

CarGurus4 wheel drive does not work - When I put the Sub in 4 wheel drive, low of high, ...Asked by Robert_Holland_073 Dec 17, 2009 at 04:06 AM about the 1994 Chevrolet Suburban K1500 4WD ... it can seize up and then the trans case may ingage but the hubs won't be locked in so it ... 1999 Chevrolet Suburban K2500 LT 4WD.

Chevrolet Tahoe Suburban 4 Wheel Drive Indicator Lights - Car ...

forums.edmunds.com > Chevrolet > Chevrolet Suburban

Oct 2, 2007 - 31 posts - ‎19 authors
My 1999 Tahoe (odo reading 137,400 miles) won't go into 4 wheel drive. .... I have a 98 suburban 1500 4x4 LT 5.7 L with 165,000 miles ... I recall once forgetting todisengage 4WD and I could feel a terrific binding when I ...
Step by Step Troubleshooting 4wd 4x4 88-98 Chevy GMC ...? 21:32https://www.youtube.com/watch?v=Su9Dkrfd_ZgJan 20, 2014 - Uploaded by rwdellingStep by Step Troubleshooting 4wd 4x4 88-98 Chevy GMC Truck. rwdelling .... Mine is acting like it is NOT pulling with the fronts,won't engage. ... Have you ever adjusted or the shift cable on your 1500 Chevy ... GM 246 transfer case, 2000 Chev Suburban- Duration: 20:09. by spelunkerd 286,045 views.GM Troubleshooting Part 13 - 4WD vacuum actuator & cable ...? 5:11https://www.youtube.com/watch?v=CbEF6PyJdU0Feb 3, 2011 - Uploaded by mr diyguy123I tacked on this video about the 4wd sys. ... I have a 1994 ChevyS10 ... My S10 won't let you go to 4 LO when your in gear. ... the front end to keep them disengaged. when you put it in 4wd, the vacuum actuator pushes a gear ...

have truck running,,put shifter in neutral,,shift into high lock 4x4,then put truck into gear,,u can shift from high lock to high gear,,from two wheel to four wheel,,in high only,,if u want to shift transfer case in low,,u have to put truck in ,,neutral,,first,,

put your truck in neutral put it in 4 wheel drive put your truck in reverse for 4 or 5 feet then put it in drive and thats it.

hi
if you think the four wheel drive it not being use it very likely that the link that engages the four wheel it rusty or the gear shift inside the gear box will not slide by some wearing abstraction caused by wear and tear

ARE YOU DOING IT WHILE IT'S IN NETRUAL, BEFORE YOU PUT IT IN GEAR AND WAITING FOR IT TO ENGAGE? IF NOT THAT IS YOUR PROBLEM.

Normal thing that happens as long as onone (worked) on it, is the vacume hose going to the engage sevevo under the battery box has fell of on either end or is brocken on the way there. Then the once or now leaky battery acid ate up this same servo. then the cable going to the front axel breaks sticks falls off or even someone needing one climbed under your truck while parked somewhere to get one to replace their brokeen one now you don't have one then theaxel engage arm or gearset is damaged

Yes it is a 700R4. They went to a 4L60E in 1993. Good Luck

Replace the push button selector assembly. Common failures. If that isnt the problem then the encoder motor on transfer case has failed. Try switch first.

Theres a vacume dash pot under the battery box. It pulls a cable that engages the front diff. Put the vacume line and you'll have lights and four wheel drive. (it happened to my blazzer)

the connections near the front axle that activate the motor to engage the system aren't melted? That's a comon problem for that body style. If there good, sounds like it could be that motor itself. To figure out if it's you motor or transfercase, jack up the rear end, have a friend inside shift into 4 wheel drive, or try to, and put it in gear and apply some gas. If the front driveshaft is turning then it's something with the front end. If not, farther back in the system.