Question about Toyota Previa

Open Question

How to replace front wheel bearing on a toyota estima

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

Ad

blownone94

  • 19 Answers

SOURCE: Replacing front wheel bearing

The brake rotor needs to be removed, drive shaft nut in center of hub then 3 bolts hold the hub assembly to spindle from back side. if it has abs unplug it then some work will need to be done with a hammer and chisel to work the bearing out of spindle and axle shaft from bearing

Posted on Oct 16, 2008

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

luis_costa

  • 18 Answers

SOURCE: wheel bearing replacement left front

Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Posted on May 08, 2009

alex whitford

  • 98 Answers

SOURCE: How is front wheel bearing replaced on a 2001 Volvo S40?

most front wheel bearings are pressed in you half to take the whole control arm off pull out the hub press out the bearing grease the new one and press it in its best to take it to a machine shop do not try pressing it in yourself

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Toyota 4 runner 2 wd front wheel removal


Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

Nov 26, 2015 | Toyota Cars & Trucks

1 Answer

How to replace a front wheel bearing on a 1995 toyota surf


I do not know but I ended up have to get a replacement wheel assembly on my Toyota Corolla. I replaced the wheel bearing it self 3 times in 6 months. Do not know if the assembly was damaged when the inner race was pressed out / in.

Make sure you know what you are doing and use a very reputable machine shop that has experience with Toyota wheel bearings.

Best, Jim

Mar 08, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

Got 3 bolts off wheel but stel cant get ball barings out to change is there any way to get them out of toyota estima enima please


not quite enough info, but the bearings usually need to be pushed out in a hydraulic press

Apr 22, 2010 | 1993 Toyota Previa

1 Answer

Hi, I own Toyota Emina Estima TD permanent


There may be more to it.. Transmission- P.T.O(Front wheels)-Rear Differential(Rear wheels). Or may have Transmission-Transfercase drives front differential(Front wheels) and rear differential(Rear wheels). So if one was rebuilt there should still be another that is still the root of the problem. Find out what exactly was rebuilt.

Apr 19, 2010 | 1996 Toyota Previa

2 Answers

How do i do an oil change on my toyota lucida estima


I believe you can find some guidelines in the following free download, good luck!:)

Contains:


Air Conditioner
Brakes, Wheels & Tyres
Cam belt
Central Locking Stuff & Alarms
Cooling System
Cylinder Head
Electrical System & I.C.E
Engine
Exterior Lighting
Fuel & Emissions System
Suspension & Steering
Transmission Systems

Also contains:

Estima Guide
Estima Owners Handbook

Download (~50MB): http://www.mediafire.com/?yx9wiypm6t2

Jul 25, 2009 | 1996 Toyota Previa

3 Answers

Shaft at front of engine making noise?


replace propshaft couplings about 40 on ebay also known as donuts .

May 04, 2009 | 1995 Toyota Previa

1 Answer

Noise coming from rear wheel passengers side rear


like grinding sound ??
if so it's your wheel bearing.

Jan 08, 2009 | 1997 Toyota Previa

1 Answer

Wheel bearing


HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Jun 28, 2008 | 2003 Toyota Corolla

2 Answers

1995 Toyota Celica Front Wheel Hub


can u replace the bearing in the hub? will that fix your problem?

May 25, 2008 | 1995 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

773 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...