2003 Hyundai Accent Logo

Related Topics:

Marietta Brown
Marietta Brown Posted on Apr 30, 2012
Be the first to answer

Change high mounted rear stop light - 2003 Hyundai Accent

Answer This Question

3 Related Answers

Anonymous

  • 1 Answer
  • Posted on May 03, 2009

SOURCE: 3rd light

This can be done one of two ways first there are two gold screws located in the trunk compartment one of them attaches the wire connection to the actual high bulb assembly this is located in a square hole. The second in in a small hole covered by foam tape these two screws will free up the assembly so you can pull the back of it up then push the front forward there should be a few clips that hold it down. This gives you access to the bulb. The second way is the hard way and more time consuming this is what i did before i figured out the first way. And that is taking your entire cabin apart. So just do it the first.

Ad

Anonymous

  • 776 Answers
  • Posted on Jun 28, 2009

SOURCE: bulb replacement in hyndai sonata high mounted rear stoplight

Research revealed no available illustration of procedure. If memory serves, there are two 'access' plates on either side of the lamp assy (popped out with small screwdriver) and two phillps screws retaining the assy in place. Remove the access plates (plastic) and the screws behind them.. access is gained.

Anonymous

  • 104 Answers
  • Posted on Jun 06, 2010

SOURCE: changing high mounted stop light bulb

HMS Lamp will be mounted in roof or in rear parcel tray.

You have to locate the screws which will be closed/covered by a dummy cap. Remove the cap and unscrew the assembly, you will be able to replace the bulbs

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I remove rear spoiler on my 2019 Lincoln mkt.
Gary,


check here....

https://www.carcarekiosk.com/video/2012_Lincoln_MKT_3.7L_V6/lights/center_brake_light
Read full answer
Jun 16, 2023 • Lincoln Cars & Trucks
0helpful
1answer

How to change high mount brake light bulb in a 2002 lincoln navigator
Instructions
    • 1 Open one of the rear doorsicon1.png of the LS. Position yourself on your knees in the back seat, facing the rear deck or rear dash.
    • 2 Remove the cover from the high-mount brakeicon1.png light assembly, by hand. Pull the cover toward the front of the vehicle. Do not pull extremely hard, or you will break the clips that mount through the deck from the trunk.
    • 3 Pull the old light bulbsicon1.png out of the high-mount assembly. Wrap the new bulbs in a paper tower prior to picking them up. Insert new bulbs into the assembly, by hand. Do not touch the bulb lenses with your hands directly.
    • 4 Install the high-mount cover onto the rear deck and push the cover toward the rear glass to lock it in place.


Read more: http://www.ehow.com/how_10060583_replace-upper-brake-bulb-2001-lincoln-ls.html#ixzz30cNQ559F
Read full answer
May 03, 2014 • Cars & Trucks
0helpful
2answers

HOW TO REPLACE HIGH MOUNT BRAKE LIGHT 2002 CADILLAC DEVILLE
The light will be fitted from inside the trunk. You might need to remove any trim or lining on the trunk lid. There will be 5 small nuts on the inside of the trunk lid. 2 each end and one centre. The light should drop out. It could be tight so GENTLY rock it up and down to free it.
** NOTE ** The light fitting is likely to be a sealed unit so you will have to replace the whole light as you cant get access to the bulbs.
Read full answer
Mar 01, 2018 • Cars & Trucks
1helpful
1answer

Need to replace stop light
Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif
Read full answer
Oct 18, 2010 • 2004 GMC Envoy
0helpful
2answers

2004 Dodge Dakota Quad Cab: The brake lights wont light up at the rear of the truck and the Center High Mounted Stop Light wont turn off.
Im having the same issue on my 04 Quad Cab Dakota. Changed out the brake light switch but still no brake lights. You have any luck ?
Read full answer
Oct 09, 2010 • 2000 Chrysler Concorde
0helpful
1answer

Changing high mounted stop light bulb
HMS Lamp will be mounted in roof or in rear parcel tray.

You have to locate the screws which will be closed/covered by a dummy cap. Remove the cap and unscrew the assembly, you will be able to replace the bulbs
Read full answer
Jun 05, 2010 • 2006 Hyundai Sonata
0helpful
1answer

How do i change a brake light bulb on 2000 vw jetta?
Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional
Read full answer
Mar 13, 2010 • 2000 Volkswagen Beetle
0helpful
2answers

My stop lights on the rear and the high mounted stop light stop wroking on my 1999 Lincoln Town car. I changed the bulbs in the hig mounted and it still does not work.
sounds like the brake light switch.
Read full answer
Nov 11, 2009 • 1999 Lincoln Town Car
2helpful
1answer

Toyota '94 Cover of high-mounted stop light won't come off
The cover under the rear windshield DOES come off and you need to finagle it a bit to get it to come loose. Try to push in on both sides while lifting up and pulling towards you or pushing on the front while pushing up. There are a couple of plastic clips that hold it on, but once you get any one of them to come loose the whole thing will come off, promise!!
Read full answer
Oct 07, 2009 • 1998 Toyota Tercel
0helpful
1answer

Changing the bulbs in the window brake light
Here ya Go!

REMOVAL PROCEDURE
  1. Open the rear compartment lid.
  2. Rotate the high-mounted stoplamp socket(s) counterclockwise to release from the high-mounted stoplamp.
  3. Remove the bulb(s) from the socket(s).
INSTALLATION PROCEDURE
  1. Install the bulb(s) to the high-mounted stoplamp socket(s).
  2. Install the lamp socket(s) to the high-mounted stoplamp, then rotate clockwise to secure.
  3. Close the rear compartment lid.

Read full answer
Feb 11, 2009 • 2001 Chevrolet Lumina
Not finding what you are looking for?

View Most Popular

2003 Accent

  • Cars & Trucks

Related Question

How do I remove rear spoiler on my 2019 Lincoln mkt.

  • Lincoln Cars & Trucks

113 views

Ask a Question

Usually answered in minutes!

Popular Questions

New hyundai i30 has clock

Hyundai Accent Cars & Trucks

Radio Station Keeps Changing Automatically

2006 Hyundai Accent

With the ignition off, the rear tail lights won't turn off

2000 Hyundai Accent

Won't play just says 1CDE on screen

2007 Hyundai Accent GS Hatchback

What does ICDE mean on a Getz stereo MP3 player

2007 Hyundai Accent GS Hatchback

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...