Removal of Headlamp bulb?

Hope this helps and please don't forget to rate! This helps us help you' Thanks!


Removal & Installation

The headlamp is a semi-sealed beam type which uses a replaceable halogen bulb. The bulb can be replaced from the engine compartment side without removing the headlamp body.

1. Disconnect the battery cable.
   
2. Disconnect the harness connector from the back side of the bulb.
   

Disconnect the harness connector from the back side of the bulb

1. Pull off the rubber cap.
   
2. Remove the headlamp bulb carefully. Do not shake or rotate the bulb when removing it.
   
3. Install in the reverse order of removal.
   

Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation

1. Remove Headlamp (13008) as outlined.
   

Headlamp Assembly
Removal and Installation

1. WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
   Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
   

1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
   

1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.
   
   
   Headlamp Assembly (Taurus Shown, Sable Similar)
   
   
   
   

1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
   

1. Remove screw from park/turn signal housing.
   

1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
   

1. Remove parking lamp from vehicle.
   

1. To install, reverse Removal procedure.
   
   
   Front Lamp-Lamp Assembly, Taurus
   
   
   

Section 17-01: Lighting, Exterior 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Headlamp Assembly Removal and Installation

1. WARNING: THE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HEADLAMP BULB AND RETAINER (13N021) ARE DROPPED. HANDLE BULB CAREFULLY. GRASP HEADLAMP BULB AND RETAINER ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HEADLAMP BULB AND RETAINER OUT OF REACH OF CHILDREN.
   NOTE: The headlamp (13008) on this vehicle does not need replacement when the headlamp bulb and retainer burns out. Refer to Headlamp Bulb for removal and installation of headlamp bulb and retainer .
   Position headlamp in the OFF position.

1. Remove headlamp dash panel junction wire (14290) from headlamp bulb and retainers by grasping wires firmly and carefully snapping connector downward.

1. NOTE: Use snap-ring pliers to spread headlamp mounting clips (13N129) , then pull straight upward to disengage.
   Remove three headlamp mounting clips attaching headlamp to radiator grille opening panel reinforcement (8A284) .

1. Remove headlamp from vehicle.

1. To install, reverse Removal procedure.

1. Aim headlamp .
   
   

SECTION 417-01: Exterior Lighting 2007 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/10/2006 Headlamp Bulb Printable View (255 KB) Expedition Headlamp
Item Part Number Description 1 13006/13005 Headlamp assembly (LH/RH) 2 13N021 Headlamp bulb

Navigator High Intensity Discharge (HID) Headlamp Bulb
Item Part Number Description 1 13N019 HID bulb access cover 2 — HID bulb screws (2 required) (part of 13A006) 3 13N021 HID bulb 4 13A006 HID bulb electrical connector and harness Removal and Installation
WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp.
NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
All vehicles

1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly in this section.

Expedition

1. Rotate the headlamp bulb approximately 1/8 turn counterclockwise and remove the bulb from the headlamp assembly.

Navigator

1. Remove the HID bulb access cover.

1. Remove the 2 screws and the HID bulb.
   • Disconnect the electrical connector.

All vehicles

1. To install, reverse the removal procedure.

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb Printable View (327 KB) Freestyle, Five Hundred
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montego
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred

1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
   • Disconnect the electrical connector.

Montego

1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.

1. Remove the 6 screws and the headlamp bulb access cover.

Montego high beam bulb

1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
   • Disconnect the electrical connector.

Montego HID bulb

1. Release the spring retainer and remove the HID bulb.
   • Disconnect the electrical connector.

All vehicles

1. To install, reverse the removal procedure.

SECTION 417-01: Exterior Lighting 2002 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Lamp Assembly —Headlamp Removal and Installation
WARNING: The halogen fog lamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a replacement bulb is installed. Removing the bolt for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed.

1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Release the ambient air temperature sensor.

1. Remove the radiator grille opening cover at the top shelf of the bumper.

1. Remove the radiator upper sight shield.
   1. Remove the pin-type retainers.
   1. Remove the radiator upper sight shield.

1. Position the headlamp assembly for removal.
   1. Remove the three bolts.
   1. Position the headlamp assembly for removal.
   • Disconnect the electrical connectors and remove the headlamp assembly.

1. To install, reverse the removal procedure.
   • If necessary, install new bulbs.
   

I will assume you are talking about the headlight?!

Removal
CAUTION: do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced life will result.

1) Disconnect and isolate negative battery cable.
2) Remove headlamp unit retaining screws. (bolts)
3) Remove headlamp unit to expose back of unit.
4) Disconnect wire connector from back of headlamp bulb.
5) Rotate retaining ring counterclockwise.
6) Remove retaining ring.
7) Pull headlamp bulb and remove from headlamp unit.

Installation

1) Install headlamp bulb to the headlamp unit.
2) Install headlamp bulb retaining ring.
3) Rotate retaining ring clockwise.
4) Connect wire connector to bulb.
5) Install headlamp unit.
6) Install headlamp retaining screws. (bolts)
7) Connect the battery negative cable.

More detailed info on how to get unit out.

Removal

1) Disconnect and isolate the battery negative cable.
2) Remove the two retaining screws.
3) Remove the upper fascia retainers by prying under the head of the fasteners with a flat bladed tool.
4) Remove headlamp unit from fender side first, then pull headlamp unit out.
5) Disconnect the wiring harness from the bulbs.
6) Remove the headlamp unit.

Installation

1) Connect wire harness to the bulbs.
2) Install headlamp unit.
3) Install the retaining screws.
4) Install upper fascia retainers.
5) Connect the battery negative cable.

I hope this will help you to get the light changed.

1997 F-250/350/Super Duty Headlamp Assembly Removal

1. Remove two screws and two nuts retaining headlamp door (13064).
   

1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
   

1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
   

1. Remove two retainers attaching upper two attachments of headlamp (13008).
   

1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
   

1. Pull headlamp from vehicle
   

96 sable, only ino I have. should be similar. Please rate, thanks

1. WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
   NOTE: A properly aimed headlamp (13008) assembly normally need not be re-aimed after installation of bulb. A burned out headlamp bulb and retainer (13N021) should not be removed from the headlamp until just before a replacement headlamp bulb and retainer is to be installed. Removal of a headlamp bulb and retainer for an extended period of time may allow contaminants (dust, moisture, smoke) to enter the headlamp and affect the performance of the headlamp. When servicing the headlamp bulb and retainer, energize the headlamp bulb and retainer only while it is contained within the headlamp body.
   
   Make sure headlamp switch (11654) is in OFF position.
   

1. NOTE: On some models the clamps holding the integrated relay control module (IRCM) may need to be unsnapped and the module pulled aside to gain access to the driver side bulb.
   
   Open hood and locate headlamp bulb through hole in upper radiator support assembly.
   

1. Remove headlamp wire connector from headlamp bulb and retainer by pulling the connector and wires in a rearward direction.
   

1. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding headlamp bulb retainer off headlamp bulb and retainer. Keep headlamp bulb retainer as it will be used again to retain new headlamp bulb and retainer.
   

1. Carefully remove headlamp bulb and retainer from opening in headlamp bulb (13007) by gently pulling straight out of opening. Do not rotate headlamp bulb and retainer during removal.
   

sorry, i only have 94 whcih is probably different. Hope it helps at least some.

Section 17-01: Lighting, Exterior 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Headlamp Assembly WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE BULB IS DROPPED. HANDLE BULB CAREFULLY. GRASP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP BULB OUT OF REACH OF CHILDREN.
Removal and Installation

1. Place the headlamp switch (11654) in the OFF position.

1. Remove the electrical connector from the miniature bulb (13466) by pulling it rearward.

1. Remove three nut and washer assemblies from the rear of the headlamp (13008) .

1. Remove the headlamp by pushing forward on the headlamp bulb and retainer (13N021) assembly. For ease of removal, it may be necessary to loosen the attachments of the adjacent parking lamp (13200) and cornering lamp assemblies.

1. Remove the three clips attaching the headlamp to the headlamp bulb retainer (13N019) by prying them out from the base using a flat-blade screwdriver. This completes the removal of the headlamp . Save the clips for the installation of the new headlamp .

1. To install the aerodynamic headlamp , ensure that the black rubber shield is securely crimped to the headlamp , then reverse Removal procedure.

1. After headlamp installation, check headlamp aim and adjust as necessary as outlined under Adjustments.

1. Turn headlamp switch on and check for proper operation.
   
   
   
   
   Item Part Number Description 1 13200 Parking Lamp Assy 2 14290 Headlamp Dash Panel Junction Wire 3A N621906-S301 Nut (2 Req'd) 4 13A093 Headlamp Adjustment Screw and Nut Assy 5 13008 Headlamp Bulb A Tighten to 4.4-6.4 Nm (39-57 Lb-In)