Cylinder head torque settings for toyota quantum 2.7 vvt and main bearings and big ends bearings. torque specifications

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

You just go to the link I attached I'm sure you will get the solution of your problem -

https://www.reliable-store.com/products/toyota-1kr-engine-workshop-service-repair-manual

This manual has everything but cam torque

http://www.championbrands.com/aera-torquespecs.pdf

This manual has what you are looking for.

http://www.championbrands.com/aera-torquespecs.pdf

They should be in this link.

http://www.championbrands.com/aera-torquespecs.pdf

Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

hi lucille.
this is all i could.
go to this link and scroll the page you might fond something to help you out.
Torque settings on big end bearings and cylinder head on 2 5 d4d quantum...

Toyota Yaris Main and Big end Torques:
Tighten the main and big end bolts in sequential order and in steps two steps.
- Main bearings. Stage 1. 30 Nm.
Stage 2. 59 Nm.
- Big end bearings. Stage 1. 15 Nm.
Rotate further by 90 degrees.

1997 Toyota Prado 5VZ-FE
Cylinder head bolts:
Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Use a factory service/repair manual. You cannot rely on a possibly wrong answer from this forum.