2001 Chrysler Town Country LXi Transaxle module
Hi there:
The DTC P0700 is a Information Code The Transaxle Control Module (TCM) that monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.
This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it, which can only be done with a diagnostic scanner. The self retreival method for chryslers with the ignition key will not pull up the specific transmission fault codes in the TCM.
Hope this helps.
SOURCE: where is the body control module located on a 1997 town & country
It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket
SOURCE: Where is the Body Control Module located?
It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the bcm.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the bcm to the jb. Slide the bcm downward to disengage guide studs on jb from channels on bcm mounting bracket
Remove bcm from jb.
SOURCE: error codes 442 and 456 on 2003 Chrysler Town and Country
Could be the gas cap. Do you fill the tank with the engine running?
Otherwise, check the hoses near the Evap canister. I have 2003 T&C and had the small leak and large leak codes. I looked at the evap cansiter and the hose coming from the fuel tank vapor line had a huge crack in it, to the point it had fallen off the evap caniser. I trimmed the end of the hose and reconnected and voila, no codes.
The evap canister is on the driver's side of the van, underneath, slightly behind the drivers seat.
BTW, to clear the codes without an OBDII reader, remove the negative cable for 5-10 minutes (15 to be safe). The computer resets and clears the codes, except for one that it sets saying loss of power to the memory.
SOURCE: radiator fan relay,2001 chrysler town country
the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays
SOURCE: 2002 Chrysler Town & Country Evaporator leak
THERE ARE SEVERAL EVAP HOSE LEAK SPOTS ON THESE VEHICLES..UNDER VEHICLE BY EVAP CANISTER,UNDER AIR CLEANER..ALSO LDP VENT VALVE NOT HOLDING VACUUM WILL SET A LEAK CODE..SMALL BLACK VALVE WITH A HOSE ON EACH END WITH A SMALL VACUUM HOSE ON TOP..IT SHOULD HOLD VACUUM WITH HAND HELD VACUUM PUMP..HAVE ALSO SEEN SPLIT HOSES NEAR EVAP SERVICE PORT LOCATED NEXT TO AIR CLEANER HOUSING
1,206 views
Usually answered in minutes!
mistake on codes 0700 and 661 & 662 shows up
P0661 Intake Manifold Tuning (IMT) Valve Solenoid Control Circuit Low Voltage
P0662 Intake Manifold Tuning (IMT) Valve Solenoid Control Circuit High Voltage
I suggest to check some short or replace this sensor.
This error came up today
×