Question about 2011 Chevrolet Silverado 2500HD

Open Question

Fault code P2463 on 2011 Chevy duramax 6.6L now has ruduce power

How do I get it to clear up, when I clear the code, it goes to keep driving cleaning exhaust filter and 20 seconds later goes to reduced power

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 379 Answers

SOURCE: code PO118 chevy blazer 2002,after intake gasket replacement

hi john , sure sounds like you may have unplugged the coolant temp sensor or didn't get a good connection at the sensor , location , in between two exhaust ports on the side of the engine that has the oil fill and pcv .

J5

Posted on Jan 27, 2009

Ad

Mike G

  • 98 Answers

SOURCE: how do i read codes for my 91 chevy silverado?

Under the dash board there is an electrical block with nothing plugged into it. there are 2 rows of terminals. on the top row on the right is terminal "a". terminal "b" is the second one in from the right. terminal diagram labeling is like this from left to right.
top row,"F", "E", "blank","C","B","A"
bottom row "G","H", "blank","blank","blank","blank"
take a small piece of wire and jump terminal "A" and "B". i found an unfolded paper clip works well. with the terminals jumped, turn the key to the on position.(DO NOT START ENGINE) with the key on, the service engine light will start flashing codes. count the flashes. it will repeat each code 3 times before moving on to the next code. your first and last code will be a code 12. that is just the test code. it lets you know you did it right. you will see 1 flash with a short pause then 2 flashes. after you see that 3 times, your next code will be your trouble codes. when you see code "12" again, there are no more. if you tell me what the codes are, i'll tell you what the mean. hope this helps.

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What could be causing my 2000 Chrysler 300m to start up but I have to pump the gas to keep it running and when i do this it backfires


Hi sounds like a blocked main jet in the carby :::: a good tune up might fix youre problem with it backfiring ::::,& replace the fuel filter : Cheers

Oct 28, 2016 | Chrysler Cars & Trucks

2 Answers

Throttle position sensor 06 grandprix gt


O2 sensors can cause this and often they clear up after a good run.

Nov 20, 2013 | 2006 Pontiac Grand Prix

1 Answer

No power when I push the gas


check for plugged exhaust system, dirty air filter, vacuum leaks, those have a mile of vacuum hoses. Also, check for bad fuel pump.

Feb 17, 2013 | 1983 Cadillac Eldorado

1 Answer

GMC 2500 Diesel, reduced engine power??


Just my 2 bits, go through a spring cleaning checklist. Plugs could be fouled up, fuel could be contaminated, you already did the filters. Do you have it chipped or programed? Change the exhaust lately? Do you have the code number? Autozone will scan it for you for free, tell you the code number. Again, just my 2 bits.

Dec 24, 2012 | 2004 GMC Envoy

2 Answers

It doesnt do it usually when driving but if the engine is at normal operating temps and after a shut down for a few minutes it is dificult to start and the reduced engine power light flashes on the screen...


You are not supposed to just clear the codes, but read them and interpret them.
The reduced engine power light means it is going into limp home mode.
You then are not supposed to drive it.
Tell us the codes and them maybe we can help you.
Don't keep driving it, or you will eventually get totally stuck.
The codes are extremely important, and should be fixed.

Nov 18, 2010 | Chevrolet C2500 Cars & Trucks

2 Answers

Chevy malibu displays engine power reduced


It's fuel related, check your fuel filter to see if it's clogged, let me know. Good luck, Jim

Sep 10, 2009 | 2006 Chevrolet Malibu

2 Answers

OBD II Test Shows a Malfunction in the MAFs (Massive Air Flow) S


The O2 sensor located on the exhaust system must be checked.
Sensor and wiring must be tested using a multimeter.

Same thing for the MAF sensor located on air intake.

Aug 24, 2009 | 2002 Honda Civic

1 Answer

Car goes in limp mode when seeing boost


Some K&N air filters are an "oil-soaked" filter and it is that oil that can cause the problem you are having. If you want to be sure, remove the filter, clear the code(s) then drive the car. If the code(s) do not return, install a non-oil-soaked filter.

Jul 08, 2009 | 2004 Pontiac Grand Prix

3 Answers

Buick Regal 2002 3.8


Have you tested the MAF sensor, disconnect the MAF sensor and see if the problem goes away, if it does replace the MAF. Disconnect the battery to clear the code.

Jul 21, 2008 | 2002 Buick Regal

Not finding what you are looking for?
2011 Chevrolet Silverado 2500HD Logo

Related Topics:

2,142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...