How do i switch my drl lights from my headlights to my signal lights on my 2007 dodge caravan

A UK car not USA not canada. bingo now known.
DRL can be super hard to fix.(diagnose)
1:get a shop to fix it, drive there in day light.
2:check all fuses?
3:scan the PCM (bcm) for DLR errors .

the DRL on some cars have SUN sensor on the dash
clean off the dust there yet? hummmmmm!
some cars this sensor as a know adjustment called sensitivity covered in the glove box users manual;.

you have a short
if you check your plug that connects the van to the trailer
take it off clean it up and rescue all wires back into place

DRLs generally run at lower power than regular lights by cycling on and off rapidly. DRL's are probably not compatible with your HID kit. Pull the DRL fuse, they are not required by law in the US,

It can be faulty low beam lamp or its connection issue for low beam lamps.

There are few solved helps links with proper solution to troubleshoot these issues.I suggest you to refer the links below.Click the link:----
Passenger side low beam out?

http://repairhelpcenter.blogspot.com/2012/01/passenger-side-low-beam-out.html

------------
Low beam HID light goes out? http://schematicsdiagram.blogspot.com/2012/01/low-beam-hid-light-goes-out.html
----------2007 Dodge Caliber: Low Beam Headlight Not working http://technoanswers.blogspot.in/2012/06/2007-dodge-caliber-low-beam-headlight.html
-------------Chevy Tahoe: Low Beam Lamps are not working? http://technoanswers.blogspot.in/2012/04/chevy-tahoe-low-beam-lamps-are-not.html
----------2001 Chevrolet Tahoe: Both Low Beam Lamps Not Working? http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-both-low-beam.html
--------------2002 Toyota Tacoma: Low Beams not working? http://technoanswers.blogspot.in/2012/04/2002-toyota-tacoma-low-beams-not.html
-----------Low beam headlights Modification? http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html
-----------DRL and Low beams not working? http://schematicsdiagram.blogspot.in/2012/04/drl-and-low-beams-not-working.html
-----------These will help.Thanks.

These trucks are known for bad multifuction switches.
the switch that i talk of is the signal switch , the handle is the switch, it bolts to side of steering column . this switch controls the signals and the headlights and high /low beams. the other thing is the headlight switch connector, the connector some times goes bad and starts to melt or just comes out of the connector. you will need to remove the cover to steering column, the screws are located under the bottom cover in holes. remove cover and check connector and then test for power if you have power going into switch but not coming out then switch is bad.

the last thing is to make sure the bulbs are good , make sure the headlight bulbs are good , and also the driving light bulbs, test for power at the connectors to those lights to.
You will need to do a little testing to find the problem.

You will need a drl bypass. You can get it for $15 -20 dollars at any hid suppliers. I know because I have the same vehicle and I have hi/lo hid.

[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."

2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]

My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

My 2007 RAV4 Limited DRLs are the regular hi beams running at what looks like 1/2 voltage (6V?). I've installed an HID system for the lo beams and would like to do the same for the hi beams but don't see how would work with the stock DRL system.

DRL function is built into the body control module. If your car doesn't have DRL, you'll need to do a full reprogramming on the BCM. Not feasible. Plus, adding HID to halogen headlight assembly is a horrible idea and *******.
Are HID kits legal Ricks Free Auto Repair Advice

You can not bypass you drls. I just put a hid kit in my 97 yukon. You have to buy a wireing harness that hooks into your harness currently on your truck. The only way to shut you dlrs off is you e brake