Question about 2008 Chevrolet Avalanche

1 Answer

Power door lock on chevy equinox does not work on one door how can it be fixed

Power door lock won't work on drivers door can only be locked/unlocked manually

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem but on the passenger side door. The wire harness on the passenger side had broken wires. Purple wire was for the lock and thicker blue and darker grey was power for the windows. I used butt connectors to repair and it worked like a charm. Area was tight to work in between vehicle frame and door. Was easier to remove door panel and disconnect harness at vehicle frame and pull harness through door to complete the repair.

Posted on Jul 07, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: 2005 chevy equinox rear hatch not locking

I've had the exact opposite issue with my 2005 Equinox.
My rear door is locked and will not unlock.

Posted on Mar 28, 2010

Anonymous

  • 1 Answer

SOURCE: door locks and power window

Just did this procedure I got from coloradofans.com forums:

"any type of power/voltage change seems to trigger this issue

The most common symptom is power locks fail and only the driver window quits, however that is on the extended cab.

Steps to fix and it works every time.

take door panel off driver's door
Disconnect the wiring attached to window and power lock control unit
disconnect battery cables
connect the negative to the positive cable(((NO BATTERY CONNECTED)))
This will act to short residual voltage in the system

5 minutes later
place the key in the ignition and turn to the run position
connect the wiring to the window/lock controller
connect the negative cable to the battery
then the positive
open drivers side door
turn key to the off position((do not remove yet)) you should get a series of dings through speakers telling you the key is still in the ignition
once it begins dinging pull the key out and you should hear the door lock solenoids trigger and the windows should work." - Coloradofans.com forums

Posted on Mar 20, 2010

keemo68

Ronald Mueller

  • 1263 Answers

SOURCE: Power door locks won't unlock + tailgate won't open

your issue involves the master control switch panel on the drivers side and or the passenger side as well some how the contact inside the switch assembly has either shorted out or no longer makes contact for the unlock side of the circuit. replace the drivers side panel switchs it's either a series of switc hs or mostimes one sigle board of switchs. you are better off going to an auto parts store rather than a GM dealership this will save you quite a bit on cash on the parts. now as to the rear tailgate. if it is electronic controled and there is an issue with the master switch you can,t manually unlock it because of a safty issue built in the system. you can manually unlock the passenger compartment doors for thew same reasons of safety but doesn't apply to the tailgate. just replace the parts and this will take care of the problem

Posted on Apr 18, 2009

Anonymous

  • 1 Answer

SOURCE: 2003 Chevy Avalanche rear doors won't lock automatically

The rear doors will not lock with the keyless remote, the drivers master switch

Posted on Jul 30, 2009

sonofadocker

Michael Rich

  • 11 Answers

SOURCE: 2001 Chevrolet Impala Door Locks Suddenly Quit Working

Passenger side of the fender under the hood - check the fuse relay box - about $12.00 a piece - they do go bad from time to time.
exchange the power lock relay with another one and test the locks.
then put the relay back and go to the autostore.

Posted on Aug 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power door lock - can't use key to unlock door


need to remove the door panel and check the clips that connect to the locking rods possiblr damaged or disconnected

May 11, 2013 | Buick Regal Cars & Trucks

1 Answer

Chevy equinox power door and power window will not work on driver door all others work


Check wire harness in passenger door pull plastic sleeve back repair wires and your window and door will work I had the same issue.
My window didn't work and door didn't lock had about 6 broken wires cost 7 bucks for some wire easy fix.

Apr 21, 2013 | Chevrolet Cars & Trucks

1 Answer

The power window and lock on my 2008 chevy equinox stopped working


The harness at the drivers door is a common problem on the Equinox, you maybe able to fix the wires but it may be less expensive just to replace the harness.

Mar 20, 2013 | 2008 Chevrolet Equinox

2 Answers

1990 Audi 100 key won't lock or unlock doors


This is usually caused by broken plastic parts in the lock system. The best would be to verify and lub all locks and check out the elecrical.
-------
kess v2

Mar 13, 2013 | Cars & Trucks

1 Answer

2002 Expedition driver door won't lock/unlock with remote


This sounds like you may have a bad lock actuator, there is an actuator that controls the lock, it may need replacing, you will need to remove the door panel to gain access to it, then with a testlight you will test to make sure the actuator is getting power and a ground and if it tests good for power and ground then replace it and door lock will start working again, this part is about 30.00 dollars. here is a picture of it. good day3_10_2013_6_17_11_pm.jpg

Mar 10, 2013 | Cars & Trucks

1 Answer

Power door lock switch?


Sounds like the drivers door lock switch is bad an as far as the auto start remote the contacts under the button get dirty and won't make contact, open the remote like changing the battery and you can probably get at the contact button, if it's a little carbon button they can be cleaned with a pencil eraser and then paper tower with a bit of rubbing alcohol, if it's an actual switch you can try spraying some contact cleaner into the switch. let it dry before you put the battery back in.

Nov 11, 2012 | Ford F-150 Cars & Trucks

1 Answer

2006 equinox drivers door lock not working


Test to see if you have power going to the door lock motor, if you do, then motor is bad, if you don't then there is a shorted wire or switch

Jun 09, 2012 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

8,813 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...