Front seat removal pt cruiser

Question edited for clarity and errors.
Question moved from Seat, (Spanish car company) to PT Cruiser.

You would be better to fly, or put her in the back seat with lots of pillows and use the centre lap strap as a seat belt.

If you pull the seat all the way forward and remove the headrest, you should be able to see the maximum recline, but electric seats have a stop on them.

Question moved from the Seat category. Pronounced: 'See-At' they are a Spanish car manufacturer forum. Moved to Chrysler PT Cruiser category.

It is a known issue. You just need a new lever.

https://www.google.com/search?q=PT+Cruiser+seat+lever

Moved category from Spanish car maker Seat (pronounced Cee-at), to Chrysler PT Cruiser.

Parts are available. Click on the Image tab for parts schematics.

https://www.google.com/search?q=2001+PT+cruiser+seat+parts

https://www.youtube.com/watch?v=zCOVX1APhI4

get under the front seats there are 4 bolts holding the seats in the floor plus a torx bolt for the lap belt, take seats out the back seat has 2 torx bolts at the front bottom of the lower cushion remove them and pull the bottom forward the back has 2 bolts holding it remove them and lift the unit straight up, be carefull there is wires under the front seat for the seat belt warning light carefully unhook them 1 for each seat now you need hog ring plairs and a bunch of new hog rings to secure the new fabric, use side cutter plairs to remove old hog rings carefully remove the seat covers, hog rings can be got at car glass shops the pliars can be got from summit racing or a place that sells car uppolstrytake your time and you can do it!!

The seat belt switch cannot be adjusted or repaired and, if ineffective or damaged, the entire front seat belt and retractor (drivers side) must be replaced.
For more details on this issue,click the link below:-----
http://technoanswers.blogspot.in/2012/06/pt-cruiser-seat-belt-and-retractor.html

-------
This will help.
Thanks.

if this is a diesel its a days job,DISCONNECT BATTERY UN DER PASSENGER SEAT take front grill and the front cross member off drain radiator loosen all bolts on radiator do not undo any connections on air con. jack up car remove plastic belly plate remove drivers side wheel and inner plastic arch cover ther is also a strut that needs to be removed,using a screwdiver prise off the fan timing belt then remove 4 bolts underneath that hold the radiator up you will then need to remove drivers side headlight to gain accsess to the bottom alternator bracket, with this done you can then carefully remove the alternator and remove the bush box and replace the bushes

its under passenger seat 5 mins and its out ,,2 screws then the pannel at the front allows acsess

you cant unless you unhook one end of the wires other than that remove the seat!

There may be some reasons of coming the airbag light on your PT Cruiser. Some connectors could be loose under seats or sensor of steering wheel could fail. However it is really rear. Your problem is probably caused by common problem in PT Cruisers - by broken wire on driver's seat.
Before you start doing anything disconnect a car battery. After 15 minutes remove a plastic panel from the seat (the one you can see when you open your door). Than you will see a wire in plastic cover. It connects an airbag in your seat and yellow connector under the seat. The wire breaks near to the second plastic T-shaped part (looking from the top of the seat backrest). It is located where is a pooling line and rising seat connector wire - somewhere in the center of lenght of the seat. Put the seat backrest to the vertical position, push up the black plastic cube of the line to remove it and have some room to repair the wire, cut a cloth tape. You should have ***** white and red wires. Inspect the wire about 1,5 inch from the center of the place where was the center of the T-shaped plastic keeper. The wire outside will be looking as new, but coper lines inside used to be broken. Strech slightly one by one of the 2 wires. When you find the break just cut the plastic cover in that place, remove 0,25 inch of the cover from each of cut end of wire and twist the ends or put extra 2 inch insert of the same wire. Wrap the coper wires in insulating tape neatly and tape all of the wires together with the T-shaped plastic keeper. Put on place the line udjusting a backrest of the seat, the keeper and plastic cover of the seat. Connect a battery and check it.
If you are not sure where is the place whre the wire could be broken, it is exactly 30 centimetres from the connector of the airbag. TomasS