At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Thaank you!!! Now how do I aquire the flowchart to trouble shoot these systems? My Haynes manual doesn"t have them.Thaank you!!! Now how do I aquire the flowchart to trouble shoot these systems? My Haynes manual doesn"t have them.
I have your request, please be patient until I get to my database tomorrow; is this OK?I have your request, please be patient until I get to my database tomorrow; is this OK?
AnonymousMar 12, 2014
where is the obd1 code list?where is the obd1 code list?
AnonymousMar 25, 2014
How to pull codes for the v6How to pull codes for the v6
You can't post conmments that contain an email address.
25) is mixture control continuously lean
42) is VSS circuit - vehicle speed sensor
43) is starter signal circuit
Good luck and I hope this answers your question. And remember to rate all the solutions that you get, thanx.
for code # 25 you will need to adjust your fuel mixture at your throttle body.
#42 there are usually 2 speed sensors one built into the spedometer and the other is either connected to one of your rear wheel backing plates or to your transmision.
# 43 you will need to follow your positive battery cable and check it and all points in between until you hit the starter, also check the grund cable on your battery to be sure it is tote and corrosion free. Another thing t check is there is a ground strap between the engine and the car body. As for locating a manual I would suggest trying through Google and type in factory service manual with your make model and year as some people have them posted on there web sites.for code # 25 you will need to adjust your fuel mixture at your throttle body.
#42 there are usually 2 speed sensors one built into the spedometer and the other is either connected to one of your rear wheel backing plates or to your transmision.
# 43 you will need to follow your positive battery cable and check it and all points in between until you hit the starter, also check the grund cable on your battery to be sure it is tote and corrosion free. Another thing t check is there is a ground strap between the engine and the car body. As for locating a manual I would suggest trying through Google and type in factory service manual with your make model and year as some people have them posted on there web sites.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hi, according to autozone.com, the connector is under hood, driver side, side of strut tower, mounted on strut tower. The pic below, hoewever shows it mounted to the intake manifold. This is an OBD1 connector. You must use an OBD1 scanner to extract trouble codes or use the manual procedure pasted below. Please let me know if you need an explanation of the trouble codes (please specify your engine and trouble code) or have any other questions.
All models except the 1MZ-FE engine is equipped with OBD I till 1995.
Make sure the battery voltage is at least 11 volts.
Make sure the throttle valve is fully closed.
Place the gear shift lever in Neutral. Turn all accessories off.
The engine should be at normal operating temperature.
Using a jumper wire, connect terminals TE1 and E1 of the Data Link Connector 1 (DLC1).
Turn the ignition switch ON , but do not start the engine. Read the diagnostic code by the counting the number of flashes of the malfunction indicator lamp.
Codes will flash in numerical order. If no faults are stored, the lamp flashes continuously every 1 / 2 second. This is sometimes called the Normal or System Clear signal.
After the diagnosis check, turn the ignition OFF and remove the jumper wire.
Compare the codes found to the applicable diagnostic code chart. If necessary, refer to the individual component tests in this section. If the component tests are OK, test the wire harness and connectors for shorts, opens and poor connections.
Simple tune up may help, but sounds like a poblem with ignition module or a coil pack. May check into crankshaft position sensor as well? If a check engine light is on you may have the codes read by someone with an OBD1 scanner or look online on how to jump the connection port with a paper clip & count how many times the check engine light flashes & then you can decipher the code that it's throwing, if there is one present in the ECM. Good Luck!
where is the ADL linkage located on a 1992 Toyota Camry. its inside of door frame its a obd 1 have codes pulled for free at auto parts store get code and look it up for the problem happy holidays
To erase the check engine light on a 1994 Camry, open the hood, and, in the engine compartment fuse box, remove the blue 15 amp EFI fuse for one minute. This will clear the codes. If you have a hard code; ie a malfunctioning sensor, the light will come right back on.
Thaank you!!! Now how do I aquire the flowchart to trouble shoot these systems? My Haynes manual doesn"t have them.
I have your request, please be patient until I get to my database tomorrow; is this OK?
where is the obd1 code list?
How to pull codes for the v6
×