Question about 2002 Isuzu Trooper

1 Answer

My ABS light on my Isuzu trooper remain on how can I reset

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,803 Answers

You first need to scan your Antilock Brake System (ABS) computer to retrieve the fault codes set by the system failure. The fault codes are needed to identify the correct diagnostic and service procedure to repair the broblem with your ABS system. It will do absolutely no good to reset the computer memory to turn the light out if the system failure is not properly diagnosed and repaired. This will only result in the light coming back on again.

Posted on Feb 18, 2012

  • Scott Cookman
    Scott Cookman Aug 27, 2013

    Where is this connector to read the ABS computer and what connector is it? I have a Bluetooth OBDII for use by computer and Android phone for the dash, but there are no error codes and the device is not visible to the software. I am told I can insert a code to interogate all of the computers, but have not found that yet.

  • Brian Danzl
    Brian Danzl Sep 07, 2014

    You have to use a jumper to diagnose. It shows how to diagnose ABS system in the chilton book. A mistake I made was not allowing the code to show up. This may take two to three minutes when the key is in the on position. The code should show up. There should be a reason why the light is on. Most of the time these codes are not seen becuase the correct tool or testing sequence or duration isn't practiced. I had my vehicle tested by several shops but none could see the ABS code with there tool. I tested mine using a jumper in the diagnostic plug and found the problem to be a bad relay. The relays are built into the module so the only way for to repair is finding a replacement module or remanufacturing it. Also the chilton book is for a 96 isuzu but diagnostics are the same as what I have found on the ABS system.



6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 54 Answers

SOURCE: looking to buy a 1998 isuzu trooper but the check engine light is on. should i buy anyway

you can bring your vehicle to autozone or your local parts place for a "free" computer scan where you can then recieve the diagnostic trouble codes and address the issues at hand

Posted on May 27, 2009


  • 5 Answers

SOURCE: 1996 Isuzu Trooper ABS and All Wheel Drive light on

Its a mechanical problem related to transmission.You should start from there.

Posted on Feb 13, 2009


Josue Almodovar

  • 298 Answers

SOURCE: check engine light on an isuzu trooper

Hi this code is not on the chart you should erase the code and see if it comes back and if it does then check if it's P0446 and not 445

Posted on Sep 09, 2009


Benjamin Patri

  • 3037 Answers

SOURCE: I need to reset the

To reset the engine light you need an OBDII Reader or can have it done at an auto parts store.
$39 From Harbor Freight. They have retail stores in many areas or use the following:
It plugs into the OBDII socket. It is under the dash next to the driver side door.
Select 'Erase' on the Reader menu and you are done.
Alternatively, you can disconnect the battery. This should wipe the OBD memory. Unfortunately, it will also reset the clock, the radio presets, and anything else in RAM in the car. Still, cheaper than going out and buying an OBD reader. Let me know if you have any further questions.


Posted on Apr 26, 2009


Charles McElchar

  • 389 Answers

SOURCE: how do i reset my timing beltwarning light after

You got to get it pluged into a diagnose computer to get it cleared this usually cost's more than replacing the belt. Your trooper is 1994 so best to take out the speedo and guages remove the bulb and keep a note of when its due the next one which is every 50,000 miles

Posted on Oct 28, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can I reset the abs light

1st of all check the abs sensor on the affected wheel,if its still intact,then u can scan and clear the abs fault with a lunch or all data software....or take it to a professional dealer

Nov 10, 2015 | 2002 Isuzu Trooper

1 Answer

Abs light staying on

1: get it serviced (oper guide says)
2: scan it.
3: read the FSM book on trooper, under ABS,

or no FSM.? login to and read ABS chapter.

Jul 21, 2014 | 2001 Isuzu Trooper

1 Answer

What to do with a brake booster out and the ABS light came on? 1998 Isuzu Trooper

Hi Rebecca,
Since the AntiLock Braking System utilizes the power (vacuum) boost to operate normally, the ABS indicator should come on if the booster fails. Yes, this means your ABS system is not able to function correctly, but neither are your standard brakes (as the extra pedal effort required to stop will tell you). however, your brakes DO WORK, so driving it to get the codes scanned shouldn't be too dangerous - just be ready to stand on the brake pedal with both feet and leave yourself plenty of room to stop by driving slowly and looking well ahead for stopped traffic. Once your booster is fixed, the ABS light should go off without any special reset or clearing of ECM memory. Good luck and happy motoring!

Jun 14, 2014 | 2000 Isuzu Trooper

1 Answer

Front right isolation valve circuit for isuzu trooper abs system

like the longest book on topic. no?
buy the FSM. read ABS.
or login to and read that there.

the first step is good brakes
then no air in system.
then abs.

Apr 25, 2014 | 2001 Isuzu Trooper

1 Answer

My 1999 Isuzu Trooper rear wheel "light indicator"

dust on your abs sensors needs cleaning

Jun 11, 2011 | 1999 Isuzu Trooper

1 Answer


check that the censor wires at the wheels are not broken.

Aug 03, 2010 | 2002 Isuzu Trooper

2 Answers

Check trans light power

My brake lights are out, the back, reverse, and head lights all work. My steering is fine as well as my brakes. But the warning lights for brake and ABS light up on my dash board

Feb 17, 2010 | 1992 Isuzu Trooper

1 Answer

Abs light on dash is lit brakes are good

Did some research and found that the module that connects to the ABS pump (next to battery) to be the problem. ISUZU wanted $3,200.00 to fix it. Bought one off of a wreck for $146.99 (LOL, yep, $146.99). Removed battery, disconnected the large cable going to the ABS, unclipped the 3 brake line clips on the top of the fender so the ABS pump could be removed and swapped the electronic modules- did not have to penetrate the brake lines at all. Took me 20 minutes. Restarted Trooper and ABS light went out.

May 08, 2009 | 2001 Isuzu Trooper

1 Answer

Fuel, brake, and alternator warning lights stay on.

change the charge light relay (the blue one) located offside front wing fuse box, get off ebay or from

Mar 07, 2009 | 1987 Isuzu Trooper

1 Answer

1996 Isuzu Trooper ABS and All Wheel Drive light on

Its a mechanical problem related to transmission.You should start from there.

Jan 05, 2009 | 1996 Isuzu Trooper

Not finding what you are looking for?
2002 Isuzu Trooper Logo

6,431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

85222 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides