94 Jeep Wrangler Seat Belt Installation

Hi,

if possible, you can squirt some oil in the seat belt clip before attempting to release the seat bet again. The oil should loosen the belt from the clip. Thank you.

DO NOT TRY TO FIX IT....an unsafe belt is like a gun with the safety off.please replace it asap.its an easy job to do,just remove the trim and the bolts are in front of you....

Check HERE for few engine sizes:
- 1999 JEEP WRANGLER - L4 2.5L 150ci GAS FI N P
- 1999 JEEP WRANGLER - L6 4.0L 242ci GAS FI N S

Hope this help (remember comment and rated this post).

take it to your dealer and tell them the problem they should be able to fix/relpace the seat belt

anyone have answer for this problem??? i have 05 grand cherokee with same issue.

open its cover to releas it
it may have grime or a coin in it

please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal

1. Remove rear seat cushion. Refer to Section 01-10 .
   

Seat Cushion, Rear Sedan
Removal

1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
   

1. Remove rear seat cushion from vehicle.
   

1. Remove rear seat back. Refer to Section 01-10 .
   

Seat Back, Rear 60/40 Split Bench—Sedan
Removal

1. NOTE: Safety belt bolts do not secure seat back to vehicle.
   
   Remove rear seat cushion as described.
   

1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
   

1. Remove two bolts from outboard rear seat back frame retaining brackets.
   

1. Lift seat back up and pull forward to remove from vehicle.
   

1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
   

Trim Panel, Quarter—Sedan Removal

1. Remove rear seat. Refer to Section 01-10 .
   

1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
   

1. Pull lower quarter trim panel away from body.
   

1. Remove safety belt retaining bolt.
   

1. Feed safety belt through lower quarter trim panel.
   

1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
   

1. Remove retractor anchor nut and retractor from rear quarter panel.
   

1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
   

1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
   

1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
   
   
   
   
   
   Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)

1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
   
   
   
   
   

Installation

1. To install, reverse Removal procedure.
   

1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
   

1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
   

1. Check the restraint system for proper operation.
   

Issue is not voiding the warranty so much as the safety issues. If you have an accident, Jeep will disavow any liability for any injuries.

While I wish I could also put 3 in back seat of my Wrangler, with carseats for grandkids, no way to safely go 3 across. Strongest selling point for the 4-door model.

Bolting it in a third row seat? that'd be fairly easy...just need something solid to anchor it to (like a thick piece of metal) on the underside to put the bolt through. do the same with seat [lap] belts and that should solve any law issues (actually some states i believe don't "require" rear seat passengers to be belted in, but I'd strongly suggest it for the kids safety!)...my big question is where are you finding enough room for a 3rd row seat? wranglers aren't exactly loaded on space...

as for torque...wrangler seats are fully removable (makes it easy to wash mud and stuff out) so as long as the bolts tighten down (air gun preferably, but you can arm twist em if need be) you'll be fine, just make sure everything is as secure/sturdy as the factory seats

look under the drivers seat there is a plug that may be unplugged or broken this is what tells the light to stay on plug it in or try unplugging it and see what happens, on some of the 200 and up models the seat belt light may have some affect on airbags working properly, I have not found this to be the case on 97 model.