Object fell into center console through cupholder

their is no round knob on center console --coin shelf-2 cup holders-shifter -cup holder- armrest --vents--rear audio control--12v acc--2 cup holders

why not read on alldata.com, its all there,
remove a screw?

1. Block the wheels to prevent the vehicle from moving.
2. Remove the rubber ash tray inserts and rubber mat from the console.
3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
6. Remove the center console retaining screws.
7. Adjust the parking brake to the full-up, or fully engaged position.
8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
10. Disconnect the electrical connectors, as necessary.
11. Adjust the parking brake to approximately the halfway position.
12. Remove the center console from the vehicle.
13. If replacing the floor console base, remove the following and retain for transfer:
    
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.

or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

there are about 8 torx screws (very small) near the hinge of the lid. remove those and the lid will come to remove the entire console, there are bolts on the back of theconsole accesible from back seat, and on the side of the console. easiest way to acces those bolts would be to remove the front two seats. they are held in by two bolts in front and two nuts under plastic covers in the back. raise the emergency brake lever and the console will slide up and be removed.

https://suzukipitstopplus.com/Category/3-suzuki-service-manuals.aspx


old post but , $4 you can read the manual as good as i.

on my 2010 ford escape XLT i found the keyless entry code printed on a label on the smart junction box which is inside the center console. To get to the smart junction box follow these instructions.
1. with a non-marring tool(i used a putty knike wrapped in plastic wrap), pry up the chrome trim piece around the shifter.
2. Remove the storage tray from underneath the center console armrest and leave the armrest cover open.
3. Grab the center console finish panel near the cupholders and pull straight up.
4. Pull the finish panel up and back then set it aside.
5. The smart junction box is to the right and slightly ahead of the gear shifter. There should be a label with a bar code that says FoMoCo. In the corner of this label is a 5 digit number. This is the factory code.
Hope this helps.

Hi Pamela,, if its the center armrest see if this link helps you, if not reply back and I'll try and help you more http://sciclonic.com/2010/06/install-center-armrest-console-in-first-gen-scion-xb/

Open up the armrest and in the bottom you will find a cover. Pry open this cover with a flathead and remove the two screws found at the bottom. Then remove the cup holder and unscrew the screw in the front corner on the left side(if sitting in the drivers seat) and ignore the two screws on the bottom of the cupholder. Now you can remove the armrest unit. Next, unscrew the two screws now visible after removing the armrest. Once these screws are removed you should be able to pop the plastic cover off from around the radio and components.

u need to take apart the center console..once u remove the cup holder u need to file down the little nibble just a tad bit and it will work just fine

First, you must remove the floor console bezel (the trim piece that surrounds the shifter knob). The proper method to remove this involves removing the shifter knob first. This is held in by a small set screw on the "radio" side of the knob. To remove the screw, you will need a small "hex-key" (also known as Allen key or Allen wrench). The proper size is 3mm, but you can get away with using a size 7/64" if you need to. Once loosened, I believe that the knob pulls right up and off. Make sure you do not lose the small screw. Also be careful not to accidentally contact the tip-top of the shifter while the knob is removed, as this may break off the small black plastic tip, which will require much more work to repair and/or replace the entire shifter.
Next, you should be able to remove the floor console bezel by prying gently and carefully on the corners and sides of the piece with a tool called a trim stick, or if you do not have this tool, you can get away with using a small, thin-tipped flat head screwdriver. However, this will almost surely cause some aesthetic damage to the edges of the trim.
Once this bezel is out of the way, (you shouldn't have to remove the electrical connectors on the underside of the bezel for this specific job) there are 2 screws holding down the bottom of the cupholder assembly. I believe these are both Torx - type screws, which will need either a T10, T15, or T20 screwdriver bit to remove(I'm sorry but I don't remember exactly which of the 3 sizes are used). After these 2 screws are removed, open the armrest. On the TOP of the FRONT of the armrest, just above the cupholders, are 2 more screws which should be the same as the 2 bottom screws. Remove these, then lift the cupholder assembly up and forward to remove it.

To install, simply reverse the above procedure.

Because this is my first solution posted on this site, I would love to have your feedback. Please let me know how everything goes with this project. Thank you!

Mitchell

Should be screws hidden under plugs that are the same color as the plastic. Try to remove cup holder etc there should be little pop outs. I will check on one of the kias in the lot. send me a response so I can put you at the top of the list.