My sunroof has stopped working

31 20A Sliding roof control unit 32 20A Sliding roof control unit 33 20A Sunroof roller blind control unit
https://fusesdiagram.com/audi/fuses-and-relay-audi-q7.html

from

https://www.google.com/search?q=2007+Audi+QUATTRO+3.6+fuse+for+panoramic+window

..

What about saturn vue sunroof wiring ? U want a wiring diagram ? Not working at all ?
The power sunroof system consists of the following components:
• Sunroof module
• Sunroof motor with limit switch
• Sunroof switch
• Sunroof glass, tilt/slide type, with glass sliding between roof and headliner
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Sunroof system fuse: sunroof 20 A fuse
• Ground G401

You can find free wiring diagrams here http://www.bbbind.com/tsb-wiring-diagrams-database/

First off this is controlled by a module (computer) The switch would only have five volts . 5volt reference voltage from the control module . Not knowing how to test the electrical circuit's for this could be expensive . Short out the module or 5 volt ref. voltage circuit inside the module.
Your best bet , take it to a qualified repair shop . Look at a wiring diagram here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine size . Under system click on body & accessories ,then under subsystem click sun roof . Then click search button then the blue link . Now tell me you under stand what's happening here .

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof Opening Position Switch (SOPS)
• Sunroof switch
• Sunroof motor/actuator
• Sunroof glass (spoiler type, with glass sliding above roof)
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power supply for the sunroof control module: SUNROOF 20 A fuse
• Ground from G302

Sunroof Opening Position Switch (SOPS)
The SOPS tracks the position of the glass through 2 limit switches:
• Soft stop limit
• Vent limit
The sunroof control module monitors the limit switches and based on the inputs determines the position of the sunroof glass. As a limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling down the 5 volt reference to 0 volts.
The sunroof control module understands the position of the sunroof glass based on the different input combinations through the sunroof limit switch soft stop signal and sunroof limit switch open vent signal circuits.

Power Sunroof Does Not Close
Perform the Initialization/Teach Process any time a new sunroof motor actuator is installed in the vehicle or any time an existing sunroof motor actuator is removed from the vehicle. Refer to Sunroof Motor/Actuator Initialization/Teach Process .

check fuse and relay if good than possible motor ot track problem their should be a mechanical bypass that will let you close it if stuck open the following information is courtesy of monte carlo forum

To check the condition of your original sunroof guides:

1. Gl*** in closed position.
2. Locate & remove 3 torx bolts on each side of sunroof glass. Lift glass out of sunroof opening & set aside in a safe place.
3. Locate "J" shaped cover plate at front of sunroof track assembly. Remove 2 torx bolts from each cover plate.
4. Lift up bracket to remove.
5. Inspect the plastic guides on each side. The sunroof cables attach to guides on front outer corner. Inspect this area closely for damage.
6. Do not operate the sunroof with the J plates removed.

Troubleshooting:

If the sunroof guides are not broken & the glass is a uniform height along the rear edge your problem may be a stripped gear inside the motor. The motor has a manual override:

1. Get access to the motor by removing the map light/switch console or lowering the front of the headliner.
2. Insert a large standard screwdriver into the nylon bushing at the center of the motor hub. Push up & turn the screwdriver to manually move the sunroof glass. If the unit will fully open & close manually, you most likely only need a replacement motor.

If your sunroof is stuck in the open position follow these steps to get it closed:

1. Remove the glass.
2. Try to close the unit without the glass. Many times one side will still be operational and close correctly.
3. Try to slide the inoperable lift arm forward. If it moves, slide it forward until it stops.
4. You now need to slide the original plastic guide forward to lower the arm to the closed position. Using a standard screwdriver, push it forward. The lift arm should begin to lower.
5. If the lift arm will still not fully lower, remove the J plate as explained above, sometimes the sunroof cable will need to be lifted up to allow the guide to fully slide forward.
6. Reinstall glass.

In the under hood junction box , fuse CTSY LP 15 amp . Instrument fuse panel PWR WDO CB 25amp .
Sunroof Motor Synchronization
Synchronization will be necessary anytime the sunroof module battery positive voltage circuit is interrupted. The sunroof module will be synchronized when the controller learns the full vent position. The sunroof system will ignore any open request until the system has been synchronized.
To synchronize the sunroof:

1. Turn ON the ignition, with the engine OFF.
2. Using the close/tilt up portion of the sunroof switch, operate the sunroof glass until it reaches the full vent position.
3. Verify that the system operates normally.

Once the sunroof glass reaches the full vent position, the actual position is stored in the memory of the sunroof module. The sunroof module will stop the motor one motor revolution before the defined actual positions
Hope this help ! good luck !

it sound like there is a problem with the cables _ they either streched or catching on something or just could be worn out also

I can supply you a new roof and fit it for 700 pound. Kind Regards, Hannah Salford Auto Spares

Sorry Bill but you don't the tool's or knowledge to take on this job . Control module's involved.
Which one does your vehicle have ?
Power Sunroof System Components -- CF5
The power sunroof system consists of the following components:
• Front glass control module and motor assembly
• Front sunshade control module and motor assembly
• Sunroof switch
• Front glass panel
• Front sunshade
• Power supply for the front glass control module and motor assembly logic: RAP relay
• Power supply for the power sunroof system: SUNROOF MOD fuse 40 A
Power Sunroof System Components -- C3B
The power sunroof system consists of the following components:
• Front glass control module and motor assembly
• Front sunshade control module and motor assembly
• Sunroof switch
• Front glass panel
• Front sunshade
• Rear sunshade control module and motor assembly
• Rear sunshade switch
• Rear sunshade
• Rear fixed glass panel
• Power supply for the front glass control module and motor assembly logic: RAP relay
• Power supply for the power sunroof system: SUNROOF MOD fuse 40 A

Give me some more information about this problem. May be i can help.

Ha, i just replaced one of these today. Yes they are serviceable but a pita. There is also a fix for the rear glass not closing. The rear tilt mechanisms need to be replaced bmw part number 54 13 7 240 682.