Clips on right glass how to take off - 1999 Plymouth Voyager

Special glue, check with the supply stores.

Did the plastic window retaining clips break? If so then I suggest to either fabricate metal clips, or buy them, and JB weld them to the glass. In 10 years this is the only way to defeat the plastic windoiw retaining clip problem.

Those are called sash clips, you gotta pull the inner door panel with a phillips screwdriver (power drill/driver/impact better) then pull the motor/regulator (after disconnecting your battery neg cable) and if memory serves at least one window track. (all 10mm headed bolts) Then the thing most people might miss, the little frame where the rear viewer mirror is mounted has to be loosened or removed. Once all that is done it lifts out at an angle. Many auto parts stores carry those sash clips in a "HELP!" package of generic parts. They give you two pairs for about $12, one pair is the right one. You have to get a special adhesive for remounting....

Hello, normally just the window sashes break. this is the plastic part that is glued on the bottom of the glass. you can but these asahes at your dealer. they simply just glue on with a special glue

Sash Channel Came Off Glass; Adhesive on Glass

1. Remove the door glass and lay it on a protected table.
2. Mark the location of the clip with tape.
3. Remove the adhesive with a one edge razor blade.
4. Clean the glass with Isopropyl alcohol.
Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.

5. Fill the sash channel clip with adhesive.
6. Install the clip in the marked location.
7. Reinstall the door glass and put the glass in the full up position for 24 hours.

Cut off the bottom edge of the guide with a cut off wheel. (Refer to the illustration above.)

Using a thin flat blade putty knife and a hammer, carefully remove the plastic piece on each side of the glass. (Refer to the illustration above).

Clean any adhesive from the glass using a one-edge razor blade. (Refer to the illustration above).

Clean the glass with Isopropyl alcohol.

Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.

Fill the sash channel clip with adhesive.

Install the clip in the marked location.

Reinstall the door glass and put the glass in the full up position for 24 hours.

22689012
Sash, Side Door Window
12378568 (US)
88901676 (Canada)
Structural Urethane Installation Adhesive

There are a few products sold at Autoparts stores. If you can find 3M brand or a brand with an activator, they seem to work best.

You need to do several things to prepare for the job. First, get some tape and outline the old mounting position from the outside of the windshield. Then clean the inside surface of the glass.

You want to separate the mounting clip from the mirror stem. Usually there is an Allen screw in the clip. Sometimes the clips have a spring underneath that needs to be pushed down to allow the mirror stem to slide off. Note the position of the clip, if the narrow end is up or down and then glue the clip to the glass in the same direction.

After the clip has had time to adhere, slide the mirror stem into the clip, tighten the Allen screw and you are done. You will have to HOLD the clip against the glass for at least 2 minutes when you are glueing it.

Or you can go to a Glass Installer and they can do it.

at the base of the shocks you'll see a metal wrap around clip, take a small flat blade pocket screwdriver and pop the clip out. once the clip is popped out of position the lift supports will come right off. make sure someone is there to help, the weight of the glass is heavy and by removing one support you'll need help hold the glass up while removing the other support & installing the new ones.

get a screwdriver in behind the glass and gently lever the old glass out, it just clips in with a spring clip

To replace the driver side mirror glass only, Grasp the side view glass only and pull off carefully. It is attached with clips and should come off pretty easy. Install new glass, lining up the clips and carefully push in. It is recommended you use a towel cloth over the glass for cushion and safety.

the clips let go of the glass inside the door, remove interior panel then open the 2 rubber plugs<about 2 inches in diameter and 3/4 the way up the door frame on inside> slowly raise or lower window regulator till you see the 2 torx screws that "pinch " the window clips loosen them and lower glass into clips till it bottoms out then tighten the clips, test, put back together< use lock tight on torx screws

You can buy the plastic clips from the dealer, break the old ones, there is no tool that I remember using, in fact I don't remember having any problem, are you sure the regulator is at fault? why not just replace the motor?