Question about 2001 Chevrolet Silverado 2500HD

1 Answer

Right turns ing stalls for a second tachometr drops 2001 k2500 6.0 liter

Crank sensor replaced for similar problem 3months ago no codes thjs time

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Hello, the first thing you need to do is check the throttle body bore for carbon build up. pretty common to have the the throttle body build up carbon between the throttle bore and throttle plate causing some unstable idle problems. you can clean out the throttle body bore with some throttle body cleaner and a shop rag

Posted on Feb 02, 2012

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 131 Answers

SOURCE: Oil Pan 1998 k2500 7.4 liter engine

You will have to remove your engine. You still will not have enough room to remove the pan from you big block by just trying to raise it.

Posted on Jul 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 Honda 1.6 showing P1336 code, what is the location of this code?


Only two things I have seen cause this code, the first is the crank sensor harness not routed correctly after a timing belt job or alt. replacement and the alt. belt rubs it or the timing belt has jumped a tooth or is not lined up correctly.

May 08, 2014 | 2000 Honda Civic

1 Answer

2004 kia sorento ex cranks but not start


Did you change the fuel filter?

Feb 12, 2014 | Cars & Trucks

2 Answers

2007 pontiac, solstice cam sensor replacement -is this common?


replace crank senser, first, always replace together, also chk some time double cam motores have to cam sensers.

Mar 17, 2013 | 2006 Pontiac Solstice

2 Answers

2003 kia sedona replaced crankshaft position sensor 6months ago would start again same code plus p0431,0335,0300,o303,0302. replaced sensor still gives a hard code sensors bad. tightened timing belt ,...


first why and how did you tighten the timing belt. if was loose should just replace the timing belt that belt runs the timing.the code po335 is your crank position sensor and it is coming up the engine is fight to keep the timing. replace the timing belt. the codes po300,po302.po303 are for a rarandom misfire. when was the last tune up. change the sparks plugs

Nov 02, 2012 | 2003 Kia Sedona

1 Answer

Engine will just keep cranking,stutter at times even die while driving, have replaced fuel pump, o2 sensors, now have found its more than likely crankshaft position sensor, I'm not sure where it is...


Quite often the crank angle sensor is located at the front of the engine down near the bottom pulley that sits on the end of the crank. You should see (under the grime :) ) a small sensor with a pigtail leading to wiring harness. This should be your crank angle sensor.
It might be far easier to get your vehicle checked either via a diagnostic or sometimes you can put a loop back wire in to generate basic codes. This of course depends upon the system OBD or OBDII
Then you read the codes which are usually the amount of times the engine check light blinks or similar and you then check that code against a code list. Most good workshop manuals will have code lists and information on how to check your codes.

Aug 01, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Truck not firing properly front coil pack not firing at all.


if this truck has an o2 sensor i would replace that and also make sure the cat-converter is not plugged,this would give you your powerloss and egr code,next is your coil,this may be caused by the computer or your crank sensor,look at the tone ring that the crank sensor uses and make sure its not missing teeth or broken,also check all your fuses.

Jun 12, 2010 | 1994 Ford Ranger Supercab

1 Answer

2005 jeep grand cherokee 3.7 40,000 miles. Last 8 months intermittent no crank can sit for eight hours or 10 minutes. Original battery but load tests fine. Starter replaced. Dealer had it for two days...


i had a similar problem with a gmc jimmy and changed ignition module several times before i ended up buying a new distributor and changing it out and have had no problem since 2 years ago

Apr 23, 2009 | Jeep Grand Cherokee Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...