How to remove the driver side door panel
The Chilton and Haynes manuals are your best bet. Order it at your local Autozone or goto the Library and research them online fro free. You can get most of this info for free if you have a library card directly from the Chilton Manuals perhaps the links below will help good luck.
Free Service Manuals how to find
youtube.com
Service manuals are everywhere in the internet and you should even get them if you search with the correct name. But with a little additional words you can Add:
clymer repair manual ford
pontiac service manual
clymer repair manual pontiac
free online auto repair manuals
free online auto repair manuals pdf
http://www.autoeducation.com/
http://workshop-manuals.com/
https://www.ifixit.com/
http://www.auto-facts.org/
https://www.alldatadiy.com/index.html
http://www.freeautorepairmanualz.com/
http://www.haynes.com/onlinerepairmanuals/
http://www.citruslibraries.org/
http://www.autotap.com/techlibrary/vehicle_diagnostic_flow_charts_explained.asp
auto repair & maintenance
BOOT FAILURE TROUBLESHOOTING FLOWCHART
http://www.fonerbooks.com/poster.pdf
http://www.shopjimmy.com/
A very good source on car and truck repair would be from chilton manuals. You can purchase them at https://www.chiltondiymanuals.com
or even better you can go the the public library or login with you library card to look at the chilton manuals online. you might also try looking at these videos:
free chilton manuals online
Live chat at dorman techincal support
1-866-933-2911
https://www.youtube.com/watch?v=Ij9uGuPOAJU
free chilton manuals online
SOURCE: I need to remove the door panel on my 2004 Avalanche
There are plastic clips that hold the door panel inplace .. First look for any hidden screws near the door handle . there might be a little plastic cover that you need to remove with a small screw driver to find the screws.. look under the handle also to see if there are any hidden screws . next take a flat blade screw driver and start at the bottom corner and try gently prying the door panel off . try to stay close to the plastic clips not to damage them by prying real hard .. once you have snapped them loose all the way around .. lift up on the door panel to remove it from around the window lip and out it should come.. holler if you have any problems.. usually The mirrors on the chevys are up above the panel and there is a triangle plastic cover over it on the inside .. it will pry off also gently and there are 3 nuts there that need to be removed .. use caution these fall behind the door panel ... holler if you need more. Jerry
SOURCE: I need to remove the door panel on my 2004 Avalanche
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them.
SOURCE: How do remove drivers side door panel
First you need to remove the door handle and window crank by pushing back the ring and releasing the handles. Also the arm rest will have screws into the steel door frame that must be removed. The panel itself has plastic snaps that are pushed into holes in the doors steel frame. The trick is to slide a pry bar or even two is better, one on ether side of the clip and force the pin out. You need to be patent and do one at a time. The door panels are made of a less than hard strong material and will brake apart easily especially if they are older. The clips go all the way around the lower three sides and the top will lift off the sill.
SOURCE: removing door panel drivers side to connect mirror wiring behind this panel
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
SOURCE: driver side door panel removal
Generic instructions to remove door panels:
1. Remove the screw(s) in the trim behind the door release handle and remove the trim.
2. Look for the screws in the arm rest and remove. Remove the arm rest.
3. Look for other screws (possibly under caps) and remove them.
4. Insert a wide flat blade between the door panel and the door. Find the plastic tabs which hold the panel to the door and gently pry the panel away from the door. Make sure you work as close to these plastic tabs as possible to avoid ripping the panel.
5. Work your way around the door prying the tabs out of the door.
6. When everything is free, gently lift the door panel straight up and out of the door.
7. Disconnect the electrical wires, and you are done.
8. There is a vapor barrier between the door and panel which must be gently peeled out of the way in order for you to gain access to the window and door latch mechanisms.
783 views
Usually answered in minutes!
×